On Wed, 27 Feb 2019 15:22:19 +0530
Vignesh Raghavendra [off-list ref] wrote:
On 26/02/19 11:46 PM, Sergei Shtylyov wrote:
quoted
On 02/19/2019 09:36 AM, Vignesh R (by way of Boris Brezillon [off-list ref]) wrote:
quoted
Cypress HyperBus is Low Signal Count, High Performance Double Data Rate Bus
interface between a host system master and one or more slave interfaces.
HyperBus is used to connect microprocessor, microcontroller, or ASIC
devices with random access NOR flash memory(called HyperFlash) or
self refresh DRAM(called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].
HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since Hyperbus is x8 DDR bus,
its equivalent to x16 parallel NOR flash wrt bits per clk. But Hyperbus
operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
But, Hyperbus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.
Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicate with flash.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller(HBMC) drivers call hb_register_device() to register a
single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.
Some HBMC masters need calibration/training sequence[3] to be carried
out, in order for DLL inside the controller to lock, by reading a known
string/pattern. This is done by repeatedly reading CFI Query
Identification String. Calibration needs to be done before try to detect
flash as part of CFI flash probe.
HyperRAM is not supported atm.
HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access Sequence
Signed-off-by: Vignesh R <vigneshr@ti.com>
[...]
quoted
diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h
new file mode 100644
index 000000000000..0aa11458c424
--- /dev/null
+++ b/include/linux/mtd/hyperbus.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+#ifndef __LINUX_MTD_HYPERBUS_H__
+#define __LINUX_MTD_HYPERBUS_H__
+
+#include <linux/mtd/map.h>
+
+enum hb_memtype {
+ HYPERFLASH,
+ HYPERRAM,
+};
+
+/**
+ * struct hb_device - struct representing Hyperbus slave device
+ * @map: map_info struct for accessing MMIO Hyperbus flash memory
+ * @dev: device pointer of Hyperbus Controller
I think we need a separate structure for the HyperBus controller, not just
for the slave devices...
quoted
+ * @np: pointer to Hyperbus slave device node
+ * @mtd: pointer to MTD struct
+ * @ops: pointer to custom Hyperbus ops
+ * @memtype: type of memory device: Hyperflash or HyperRAM
+ * @needs_calib: flag to indicate whether calibration sequence is needed
+ * @registered: flag to indicate whether device is registered with MTD core
+ */
+
+struct hb_device {
+ struct map_info map;
+ struct device *dev;
+ struct device_node *np;
+ struct mtd_info *mtd;
+ struct hb_ops *ops;
+ enum hb_memtype memtype;
+ bool needs_calib;
+ bool registered;
+};
+
+/**
+ * struct hb_ops - struct representing custom Hyperbus operations
+ * @read16: read 16 bit of data, usually from register/ID-CFI space
+ * @write16: write 16 bit of data, usually to register/ID-CFI space
+ * copy_from: copy data from flash memory
+ * copy_to: copy data to flash_memory
+ */
+
+struct hb_ops {
+ u16 (*read16)(struct hb_device *hbdev, unsigned long addr);
+ void (*write16)(struct hb_device *hbdev, unsigned long addr, u16 val);
+
+ void (*copy_from)(struct hb_device *hbdev, void *to,
+ unsigned long from, ssize_t len);
+ void (*copy_to)(struct hb_device *dev, unsigned long to,
+ const void *from, ssize_t len);
... else these methods won't fly if you need to "massage" the controller
registers inside them...
If accessing controller register is the only need, wouldn't a private
data pointer within struct hb_device be sufficient to hold pointer to
controller specific struct?
struct hb_device {
...
void *priv; /* points to controller's private data */
};
Or do you see a need for separate structure for the HyperBus controller?
Sorry to chime in. Just want to share my experience here: properly
splitting the controller/device representation is always a good thing.
When it's not done from the beginning and people start to add their own
controller drivers as if it was a flash device driver it becomes messy
pretty quickly and people add hacks to support that (look at the raw
NAND framework if you need a proof). So, I'd recommend having this
separation now, even if the onle controllers we support have a 1:1
relationship between HB controller and HB device.
quoted
quoted
+};
[...]
MBR, Sergei