Add bindings documentation for i.MX7 media drivers.
The imx7 MIPI CSI2 and imx7 CMOS Sensor Interface.

Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
---
 .../devicetree/bindings/media/imx7-csi.txt    | 44 ++++++++++
 .../bindings/media/imx7-mipi-csi2.txt         | 82 +++++++++++++++++++
 2 files changed, 126 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/imx7-csi.txt
 create mode 100644 Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt

diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt
new file mode 100644
index 000000000000..aab4f5d72390
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx7-csi.txt

@@ -0,0 +1,44 @@
+Freescale i.MX7 CMOS Sensor Interface
+=====================================
+
+csi node
+--------
+
+This is device node for the CMOS Sensor Interface (CSI) which enables the chip
+to connect directly to external CMOS image sensors.
+
+Required properties:
+
+- compatible    : "fsl,imx7-csi";
+- reg           : base address and length of the register set for the device;
+- interrupts    : should contain CSI interrupt;
+- clocks        : list of clock specifiers, see
+        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
+- clock-names   : must contain "axi", "mclk" and "dcic" entries, matching
+                 entries in the clock property;
+
+The device node should contain one 'port' child node with one child 'endpoint'

+video multiplexer.
+
+example:
+
+                csi: csi@30710000 {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        compatible = "fsl,imx7-csi";
+                        reg = <0x30710000 0x10000>;
+                        interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+                        clocks = <&clks IMX7D_CLK_DUMMY>,
+                                        <&clks IMX7D_CSI_MCLK_ROOT_CLK>,
+                                        <&clks IMX7D_CLK_DUMMY>;
+                        clock-names = "axi", "mclk", "dcic";
+
+                        port {
+                                csi_from_csi_mux: endpoint {
+                                        remote-endpoint = <&csi_mux_to_csi>;
+                                };
+                        };
+                };

diff --git a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt
new file mode 100644
index 000000000000..7c5f20863724
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt

@@ -0,0 +1,82 @@
+Freescale i.MX7 Mipi CSI2
+=========================
+
+mipi_csi2 node
+--------------
+
+This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is
+compatible with previous version of Samsung D-phy.
+
+Required properties:
+
+- compatible    : "fsl,imx7-mipi-csi2";
+- reg           : base address and length of the register set for the device;
+- interrupts    : should contain MIPI CSIS interrupt;
+- clocks        : list of clock specifiers, see
+        Documentation/devicetree/bindings/clock/clock-bindings.txt for details;
+- clock-names   : must contain "pclk", "wrap" and "phy" entries, matching
+                  entries in the clock property;
+- power-domains : a phandle to the power domain, see
+          Documentation/devicetree/bindings/power/power_domain.txt for details.
+- reset-names   : should include following entry "mrst";
+- resets        : a list of phandle, should contain reset entry of
+                  reset-names;
+- phy-supply    : from the generic phy bindings, a phandle to a regulator that
+	          provides power to MIPI CSIS core;
+
+Optional properties:
+
+- clock-frequency : The IP's main (system bus) clock frequency in Hz, default
+		    value when this property is not specified is 166 MHz;
+- fsl,csis-hs-settle : differential receiver (HS-RX) settle time;
+
+port node
+---------
+
+- reg		  : (required) can take the values 0 or 1, where 0 is the
+                     related sink port and port 1 should be the source one;