Shawn,

On Mon, Jun 13, 2016 at 12:58 AM, Shawn Lin [off-list ref] wrote:

On 2016/6/8 6:44, Douglas Anderson wrote:

quoted

Previous PHY code waited a fixed amount of time for the DLL to lock at
power on time.  Unfortunately, the time for the DLL to lock is actually
a bit more dynamic and can be longer if the card clock is slower.

Instead of waiting a fixed 30 us, let's now dynamically wait until the
lock bit gets set.  We'll wait up to 10 ms which should be OK even if
the card clock is at the super slow 100 kHz.

mmc stack limit the min freq to 200k when initializing the card.

Are you certain?  In "drivers/mmc/core/core.c" I see:

static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };

In ID mode if 400kHz, 300kHz, 200kHz all fail then it will try 100kHz.

So 5ms is enough, but it's ok to set the max timeout to 10ms as we
can break out if locked.

Right, it's OK to error on the long side since it is really a pretty
serious error if the DLL doesn't lock and delaying tens of
milliseconds in this case is not a huge deal.

quoted

On its own, this change makes the PHY power on code a little more
robust.  Before this change the PHY was relying on the eMMC code to make
sure the PHY was only powered on when the card clock was set to at least
50 MHz before, though this reliance wasn't documented anywhere.

This change will be even more useful in future changes where we actually
need to be able to wait for a DLL lock at slower clock speeds.

Signed-off-by: Douglas Anderson <redacted>
---
 drivers/phy/phy-rockchip-emmc.c | 27 +++++++++++++++++++--------
 1 file changed, 19 insertions(+), 8 deletions(-)

diff --git a/drivers/phy/phy-rockchip-emmc.c

b/drivers/phy/phy-rockchip-emmc.c
index a69f53630e67..8336053aea5c 100644

--- a/drivers/phy/phy-rockchip-emmc.c
+++ b/drivers/phy/phy-rockchip-emmc.c

@@ -85,6 +85,7 @@ static int rockchip_emmc_phy_power(struct

rockchip_emmc_phy *rk_phy,
 {
        unsigned int caldone;
        unsigned int dllrdy;
+       unsigned long timeout;

        /*
         * Keep phyctrl_pdb and phyctrl_endll low to allow

@@ -137,15 +138,25 @@ static int rockchip_emmc_phy_power(struct

rockchip_emmc_phy *rk_phy,
                                   PHYCTRL_ENDLL_MASK,
                                   PHYCTRL_ENDLL_SHIFT));
        /*
-        * After enable analog DLL circuits, we need an extra 10.2us
-        * for dll to be ready for work. But according to testing, we
-        * find some chips need more than 25us.
+        * After enabling analog DLL circuits docs say that we need 10.2
us if
+        * our source clock is at 50 MHz and that lock time scales
linearly
+        * with clock speed.  If we are powering on the PHY and the card
clock
+        * is super slow (like 100 kHZ) this could take as long as 5.1 ms.

5.1ms is by calculation or test?

By calculation.

quoted

quoted

10.2 us * (50000000 Hz / 100000 Hz)

5100.0 us, or 5.1 ms

I'll add clarification to the comment.


-Doug
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html