Thread (9 messages) 9 messages, 3 authors, 2015-07-31
STALE3962d
Revisions (12)
  1. v1 [diff vs current]
  2. v2 [diff vs current]
  3. v3 [diff vs current]
  4. v4 [diff vs current]
  5. v5 [diff vs current]
  6. v6 [diff vs current]
  7. v7 current
  8. v8 [diff vs current]
  9. v9 [diff vs current]
  10. v10 [diff vs current]
  11. v11 [diff vs current]
  12. v12 [diff vs current]

[PATCH v7 3/5] mtd: nand: vf610_nfc: add device tree bindings

From: Stefan Agner <stefan@agner.ch>
Date: 2015-07-24 13:17:03
Also in: linux-arm-kernel, lkml
Subsystem: memory technology devices (mtd), open firmware and flattened device tree bindings, the rest · Maintainers: Miquel Raynal, Richard Weinberger, Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds

Signed-off-by: Bill Pringlemeir <redacted>
Signed-off-by: Stefan Agner <stefan@agner.ch>
---
 .../devicetree/bindings/mtd/vf610-nfc.txt          | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mtd/vf610-nfc.txt
diff --git a/Documentation/devicetree/bindings/mtd/vf610-nfc.txt b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
new file mode 100644
index 0000000..cae5f25
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/vf610-nfc.txt
@@ -0,0 +1,45 @@
+Freescale's NAND flash controller (NFC)
+
+This variant of the Freescale NAND flash controller (NFC) can be found on
+Vybrid (vf610), MPC5125, MCF54418 and Kinetis K70.
+
+Required properties:
+- compatible: Should be set to "fsl,vf610-nfc"
+- reg: address range of the NFC
+- interrupts: interrupt of the NFC
+- nand-bus-width: see nand.txt
+- nand-ecc-mode: see nand.txt
+- nand-on-flash-bbt: see nand.txt
+- assigned-clocks: main clock from the SoC, for Vybrid <&clks VF610_CLK_NFC>;
+- assigned-clock-rates: The NAND bus timing is derived from this clock
+    rate and should not exceed maximum timing for any NAND memory chip
+    in a board stuffing. Typical NAND memory timings derived from this
+    clock are found in the SoC hardware reference manual. Furthermore,
+    there might be restrictions on maximum rates when using hardware ECC.
+
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+
+Required properties for hardware ECC:
+- nand-ecc-strength: supported strengths are 24 and 32 bit (see nand.txt)
+- nand-ecc-step-size: step size equals page size, currently only 2k pages are
+    supported
+
+Example:
+
+	nfc: nand@400e0000 {
+		compatible = "fsl,vf610-nfc";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x400e0000 0x4000>;
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks VF610_CLK_NFC>;
+		clock-names = "nfc";
+		assigned-clocks = <&clks VF610_CLK_NFC>;
+		assigned-clock-rates = <33000000>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <32>;
+		nand-ecc-step-size = <2048>;
+		nand-on-flash-bbt;
+	};
-- 
2.4.5
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help