Re: [PATCH v2 1/2] ARM: dts: dra7: Add CPSW and MDIO module nodes for dra7
From: Nishanth Menon <nm@ti.com>
Date: 2014-09-10 13:50:58
Also in:
linux-omap, lkml
On 09/10/2014 08:37 AM, Mugunthan V N wrote:
quoted hunk ↗ jump to hunk
Add CPSW and MDIO related device tree data for DRA7XX and made as status disabled. Phy-id, pinmux for active and sleep state needs to be added in board dts files and enable the CPSW device. Signed-off-by: Mugunthan V N <redacted> --- arch/arm/boot/dts/dra7.dtsi | 59 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+)diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index d678152..8d79321 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi@@ -34,6 +34,8 @@ serial3 = &uart4; serial4 = &uart5; serial5 = &uart6; + ethernet0 = &cpsw_emac0; + ethernet1 = &cpsw_emac1;
should this rather be in board dts?
quoted hunk ↗ jump to hunk
}; timer {@@ -1262,6 +1264,63 @@ ti,irqs-skip = <10 133 139 140>; ti,irqs-safe-map = <0>; }; + + mac: ethernet@4a100000 { + compatible = "ti,cpsw"; + ti,hwmods = "gmac"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + no_bd_ram = <0>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + reg = <0x48484000 0x1000 + 0x48485200 0x2E00>; + #address-cells = <1>; + #size-cells = <1>; + /* + * rx_thresh_pend + * rx_pend + * tx_pend + * misc_pend + */ + interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; + ranges; + status = "disabled"; + + davinci_mdio: mdio@48485000 { + compatible = "ti,davinci_mdio"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + reg = <0x48485000 0x100>; + }; + + cpsw_emac0: slave@48480200 { + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ];
should be disabled? what about platforms that do not have both emac ports?
+ };
+
+ cpsw_emac1: slave@48480300 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];should be disabled? what about platforms that do not have both emac ports?
+ };
+
+ phy_sel: cpsw-phy-sel@4a002554 {
+ compatible = "ti,dra7xx-cpsw-phy-sel";
+ reg= <0x4a002554 0x4>;
+ reg-names = "gmii-sel";
+ };
+ };
+
};
};
-- Regards, Nishanth Menon