[PATCH V9 2/2] ARM: dts: Enable ahci sata and sata phy
From: Yuvaraj Kumar C D <hidden>
Date: 2014-03-03 05:23:57
Also in:
linux-arm-kernel, lkml
Subsystem:
generic phy framework, libata subsystem (serial and parallel ata drivers), open firmware and flattened device tree bindings, the rest · Maintainers:
Vinod Koul, Damien Le Moal, Niklas Cassel, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Linus Torvalds
This patch adds dt entry for ahci sata controller and its corresponding phy controller.phy node has been added w.r.t new generic phy framework. Signed-off-by: Yuvaraj Kumar C D <redacted> --- Changes since V8: 1.sata@122f0000 and sata_phy@12170000 disabled by default in SOC specific dts file and enabled the same in board dts file. Changes since V7: 1.syscon-phandle name updated. Changes since V6:none Changes since V5:none Changes since V4: 1.Used the new phandle "sata_phy_i2c" in the DT entry. 2.Updated binding document. Changes since V3: 1.Moved the binding info to the /bindings/phy/ Changes since V2: 1.Used syscon interface to PMU handling. 2.Changed "sata-phy-i2c" to "exynos-sataphy-i2c". Changes since V1: 1.Minor changes to node name convention. 2.Updated binding document. .../devicetree/bindings/ata/exynos-sata-phy.txt | 14 -------- .../devicetree/bindings/ata/exynos-sata.txt | 25 +++++++++----- .../devicetree/bindings/phy/samsung-phy.txt | 36 ++++++++++++++++++++ arch/arm/boot/dts/exynos5250-arndale.dts | 21 ++++++++++++ arch/arm/boot/dts/exynos5250-smdk5250.dts | 17 +++++---- arch/arm/boot/dts/exynos5250.dtsi | 18 +++++++--- 6 files changed, 98 insertions(+), 33 deletions(-) delete mode 100644 Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt b/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
deleted file mode 100644
index 37824fa..0000000
--- a/Documentation/devicetree/bindings/ata/exynos-sata-phy.txt
+++ /dev/null@@ -1,14 +0,0 @@ -* Samsung SATA PHY Controller - -SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. -Each SATA PHY controller should have its own node. - -Required properties: -- compatible : compatible list, contains "samsung,exynos5-sata-phy" -- reg : <registers mapping> - -Example: - sata@ffe07000 { - compatible = "samsung,exynos5-sata-phy"; - reg = <0xffe07000 0x1000>; - };
diff --git a/Documentation/devicetree/bindings/ata/exynos-sata.txt b/Documentation/devicetree/bindings/ata/exynos-sata.txt
index 0849f10..b2adb1f 100644
--- a/Documentation/devicetree/bindings/ata/exynos-sata.txt
+++ b/Documentation/devicetree/bindings/ata/exynos-sata.txt@@ -4,14 +4,21 @@ SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. Required properties: -- compatible : compatible list, contains "samsung,exynos5-sata" -- interrupts : <interrupt mapping for SATA IRQ> -- reg : <registers mapping> -- samsung,sata-freq : <frequency in MHz> +- compatible : compatible list, contains "samsung,exynos5-sata" +- interrupts : <interrupt mapping for SATA IRQ> +- reg : <registers mapping> +- samsung,sata-freq : <frequency in MHz> +- phys : as mentioned in phy-bindings.txt +- phy-names : as mentioned in phy-bindings.txt Example: - sata@ffe08000 { - compatible = "samsung,exynos5-sata"; - reg = <0xffe08000 0x1000>; - interrupts = <115>; - }; + sata@122f0000 { + compatible = "snps,dwc-ahci"; + samsung,sata-freq = <66>; + reg = <0x122f0000 0x1ff>; + interrupts = <0 115 0>; + clocks = <&clock 277>, <&clock 143>; + clock-names = "sata", "sclk_sata"; + phys = <&sata_phy>; + phy-names = "sata-phy"; + };
diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
index c0fccaa..a937f75 100644
--- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
+++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt@@ -20,3 +20,39 @@ Required properties: - compatible : should be "samsung,exynos5250-dp-video-phy"; - reg : offset and length of the Display Port PHY register set; - #phy-cells : from the generic PHY bindings, must be 0; + +Samsung SATA PHY Controller +--------------------------- + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible : compatible list, contains "samsung,exynos5250-sata-phy" +- reg : offset and length of the SATA PHY register set; +- #phy-cells : from the generic phy bindings; + +Example: + sata_phy: sata-phy@12170000 { + compatible = "samsung,exynos5250-sata-phy"; + reg = <0x12170000 0x1ff>; + clocks = <&clock 287>; + clock-names = "sata_phyctrl"; + #phy-cells = <0>; + samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>; + samsung,syscon-phandle = <&pmu_syscon>; + }; + +Device-Tree bindings for sataphy i2c client driver +-------------------------------------------------- + +Required properties: +compatible: Should be "samsung,exynos-sataphy-i2c" +- reg: I2C address of the sataphy i2c device. + +Example: + + sata_phy_i2c:sata-phy@38 { + compatible = "samsung,exynos-sataphy-i2c"; + reg = <0x38>; + };
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 38b96a4..97eef40 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts@@ -375,6 +375,27 @@ }; }; + i2c@121D0000 { + status = "okay"; + samsung,i2c-sda-delay = <100>; + samsung,i2c-max-bus-freq = <40000>; + samsung,i2c-slave-addr = <0x38>; + + sata_phy_i2c:sata-phy@38 { + compatible = "samsung,exynos-sataphy-i2c"; + reg = <0x38>; + }; + }; + + sata@122F0000 { + status = "okay"; + }; + + sata-phy@12170000 { + status = "okay"; + samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>; + }; + mmc_0: mmc@12200000 { status = "okay"; num-slots = <1>;
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index 0837dd8..e0da05b 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts@@ -100,16 +100,12 @@ samsung,i2c-slave-addr = <0x38>; status = "okay"; - sata-phy { - compatible = "samsung,sata-phy"; + sata_phy_i2c:sata-phy@38 { + compatible = "samsung,exynos-sataphy-i2c"; reg = <0x38>; }; }; - sata@122F0000 { - samsung,sata-freq = <66>; - }; - i2c@12C80000 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <66000>;
@@ -132,6 +128,15 @@ }; }; + sata@122F0000 { + status = "okay"; + }; + + sata-phy@12170000 { + status = "okay"; + samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>; + }; + mmc@12200000 { status = "okay"; num-slots = <1>;
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 8f6300f..31f7cab 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi@@ -46,6 +46,7 @@ i2c6 = &i2c_6; i2c7 = &i2c_7; i2c8 = &i2c_8; + i2c9 = &i2c_9; pinctrl0 = &pinctrl_0; pinctrl1 = &pinctrl_1; pinctrl2 = &pinctrl_2;
@@ -233,16 +234,25 @@ }; sata@122F0000 { - compatible = "samsung,exynos5-sata-ahci"; + compatible = "snps,dwc-ahci"; + samsung,sata-freq = <66>; reg = <0x122F0000 0x1ff>; interrupts = <0 115 0>; clocks = <&clock 277>, <&clock 143>; clock-names = "sata", "sclk_sata"; + phys = <&sata_phy>; + phy-names = "sata-phy"; + status = "disabled"; }; - sata-phy@12170000 { - compatible = "samsung,exynos5-sata-phy"; + sata_phy: sata-phy@12170000 { + compatible = "samsung,exynos5250-sata-phy"; reg = <0x12170000 0x1ff>; + clocks = <&clock 287>; + clock-names = "sata_phyctrl"; + #phy-cells = <0>; + samsung,syscon-phandle = <&pmu_system_controller>; + status = "disabled"; }; i2c_0: i2c@12C60000 {
@@ -360,7 +370,7 @@ status = "disabled"; }; - i2c@121D0000 { + i2c_9: i2c@121D0000 { compatible = "samsung,exynos5-sata-phy-i2c"; reg = <0x121D0000 0x100>; #address-cells = <1>;
--
1.7.10.4