On Tue, Nov 12, 2013 at 09:40:38AM +0100, Pantelis Antoniou wrote:
Hi Grant,
On Nov 11, 2013, at 7:47 PM, Grant Likely wrote:
quoted
On Fri, 8 Nov 2013 17:06:10 +0200, Pantelis Antoniou [off-list ref] wrote:
quoted
Add a runtime interface to /proc to enable generic device tree overlay
usage.
Two new /proc files are added:
/proc/device-tree-overlay & /proc/device-tree-overlay-status
/proc/device-tree-overlay accepts a stream of a device tree objects and
applies it to the running kernel's device tree.
$ cat ~/BB-UART2-00A0.dtbo >device-tree-overlay
overlay_proc_release: Applied #2 overlay segments @0
/proc/device-tree-overlay-status displays the the overlays added using
the /proc interface
$ cat device-tree-overlay-status
0: 861 bytes BB-UART2:00A0
The format of the status line is
<ID>: <SIZE> bytes <part-number>:<version>
<ID> is the id of the overlay
<SIZE> is the size of the overlay in bytes
<part-number>, <version> are (optional) root level properties of the DTBO
You can remove an overlay by echoing the <ID> number of the overlay
precedded with a '-'
So
$ echo "-0" >device-tree-overlay-status
Removes the overlay.
Note that this seldom works on most platforms since platform_device
removal is something that almost never works without extra patches.
Signed-off-by: Pantelis Antoniou <redacted>
Why /proc? Did you consider using the firmware loading mechanism? While
I expressed concerned about the capebus approach, the loading of
overlays needs to remain under the control of either a driver or the
platform. By default it should not be possible to drop an arbitrary
overlay into /proc/device-tree-overlay and have things change in the
base tree. Along the same lines, I would expect for the device driver or
platform to be able to filter or limit the parts of the tree that are
allowed to be modified.
The firmware loading mechanism is the preferred way to handle it, and is
in fact what is used in practice by the whole cape manager mechanism.
But that's part of specific board support, and this is more like a general
way to use overlays, in any kind of DT enabled system.
I agree this is a) completely dangerous and b) /proc is a bad place to put
it. I put it here in order to get the ball rolling, about the proper place
to put device tree related interfaces.
The good thing about this interface is that it's always available, and
it is good for debugging (especially loading/unloading debugging).
As was pointed out earlier in the thread, /proc just isn't the place to
add these configuration interfaces any longer.
quoted
A side benefit of the firmware loader is that the kernel can obtain the
overlay on its own if needed at boot time without userspace involvement.
Yes, that is correct, and it is the way we use it on the beaglebone.
The root fs device is present on a overlay, which is built into the kernel's
firmware.
Let's be clear that there are two use cases here
1) kernel driven overlay loading
- root device configuration, other early devices, kernel-based h/w
detection
2) userspace driven overlay loading
- s/w defined h/w, hobbyist connecting stuff on a breadboard,
userspace arduino support
Combining a configfs api for userspace configuration of the overlay to
load with the firmware loader interface would address both of these.
As Grant noted, you want the firmware loader support to handle the
standard kernel driver initiated case which you were doing with capebus
already. But for userspace we have configuration to hand to the kernel
in the form of the name of an overlay. This configuration should be
provided via configfs.
Instantiate an overlay:
mkdir /config/dto/0
would create the following attributes:
/config/dto/0/overlay
/config/dto/0/status
Start a firmware load of an overlay:
echo "foo.dtbo" > /config/dto/0/overlay
[loads /lib/firmware/foo.dtbo]
Status of overlay:
cat /config/dto/0/status
0: 861 bytes FOO:BAR0
Remove an overlay:
rmdir /config/dto/0
-Matt
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html