Re: [PATCH v5 2/5] Bluetooth: hci_qca: Deassert RTS while baudrate change command

Hi Matthias,

On 2019-01-11 07:07, Matthias Kaehlcke wrote:

On Thu, Jan 10, 2019 at 08:22:12PM +0530, Balakrishna Godavarthi wrote:

quoted

Hi Johan,

On 2019-01-10 20:09, Johan Hovold wrote:

quoted

On Thu, Jan 10, 2019 at 08:04:12PM +0530, Balakrishna Godavarthi wrote:

quoted

Hi Johan,

On 2019-01-09 20:22, Johan Hovold wrote:

quoted

On Thu, Dec 20, 2018 at 08:16:36PM +0530, Balakrishna Godavarthi wrote:

quoted

This patch will help to stop frame reassembly errors while changing
the baudrate. This is because host send a change baudrate request
command to the chip with 115200 bps, Whereas chip will change their
UART clocks to the enable for new baudrate and sends the response
for the change request command with newer baudrate, On host side
we are still operating in 115200 bps which results of reading garbage
data. Here we are pulling RTS line, so that chip we will wait to send
data
to host until host change its baudrate.

quoted

quoted

quoted

+		/* Deassert RTS while changing the baudrate of chip and host.
+		 * This will prevent chip from transmitting its response with
+		 * the new baudrate while the host port is still operating at
+		 * the old speed.
+		 */
+		qcadev = serdev_device_get_drvdata(hu->serdev);
+		if (qcadev->btsoc_type == QCA_WCN3990)
+			serdev_device_set_rts(hu->serdev, false);
+

This may not do what you want unless you also disable hardware flow
control.

quoted

Here my requirement here is to block the chip to send its data before
HOST changes it is baudrate. So if i disable flow control lines of
HOST which will be in low state.  so that the chip will send it data
before HOST change the baudrate of HOST. which results in frame
reassembly error.

Not sure I understand what you're trying to say above. My point is that
you cannot reliable control RTS when you have automatic flow control
enabled (i.e. it is managed by hardware and it's state reflects whether
there's room in the UART receive FIFO).

Johan

[Bala]: Yes i got your point, but our driver

I suppose with "our driver" you refer to a Qualcomm UART driver like
qcom_geni_serial.c. Unless the Bluetooth controller is really tied to
some specific SoC (e.g. because it is on-chip) you shouldn't make
assumptions about the UART driver or hardware beyond standard
behavior.

But even if we assume that the driver you mention is used, I think you
are rather confirming Johan's concern than dispersing it:

[Bala]: now understood the point.

quoted

will not support automatic flow control (based on the FIFO status)
unless we explicitly enabled via software. i.e. if we enable the
flow, hardware will look for it else it will not looks for CTS or
RTS Line.

So we agree that the UART hardware may change RTS if hardware flow
control is enabled?

static int qca_send_power_pulse(struct hci_uart *hu, u8 cmd)
{
  ...
  hci_uart_set_flow_control(hu, false);
  ...
}

I still find it utterly confusing that set_flow_control(false) enables
flow control, but that's what it does, hence after
qca_send_power_pulse() flow control is (re-)enabled.

So far I haven't seen problems with qcom_geni_serial.c overriding the
level set with serdev_device_set_rts(), but I tend to agree with Johan
that this could be a problem (if not with this UART (driver) then with
another). I'm not keen about adding more flow control on/off clutter,
but if that is needed for the driver to operate reliably across
platforms so be it.

Cheers

Matthias

[Bala]: previously we have disabling the flow control, that is not 
pulling the RTS line if it disabled.
         so that the reason we are explicilty pulling it by calling 
set_rts() with false.

         Johan concern can be fixed either of two ways.

         1. disable the flow control, but the uart driver should pull the 
RTS line high. as the line is unused
         2. disable the flow control and call set_rts with false that 
will helps us to pull the RTS line.

will experiment more on this and post the change.


-- 
Regards
Balakrishna.