Re: [Bluez-users] IOGear GBU301 and Kernel 2.4.20

Hi Tom,

quoted

quoted

quoted

this is a Broadcom BCM2033 dongle without firmware loaded. Install the
bluez-firmware package and use the bcm203x kernel driver from a recent
2.6 kernel or compile bluez-utils-2.9 with bcm203x support.

Well, I did compile bluez-utils (and installed it) as well as bluez-firmware. 
That now seems to go well.  Now when I plug in the dongle I get the following
in '/var/log/messages':
Aug  9 16:00:02 xyzzy kernel: hub.c: new USB device 00:10.1-2, assigned address
6
Aug  9 16:00:02 xyzzy kernel: usb.c: USB device 6 (vend/prod 0xa5c/0x2033) is
not claimed by any active driver.
Aug  9 16:00:05 xyzzy /etc/hotplug/usb.agent: Setup hci_usb for USB product
a5c/2033/a0

But I still get the following in /proc/bus/usb/devices

quoted

quoted

quoted

quoted

quoted

< T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  7 Spd=12  MxCh= 0
< D:  Ver= 1.01 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
< P:  Vendor=0a5c ProdID=2033 Rev= 0.a0
< C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA
< I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
< E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
< E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
< I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
< E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
< I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=83(I) Atr=01(Isoc) MxPS=  16 Ivl=1ms
< E:  Ad=03(O) Atr=01(Isoc) MxPS=  16 Ivl=1ms
< I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
< E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
< I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
< E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
< I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
< E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
< I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
< E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
< E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
< I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
< E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
< E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
<<<<<

Do I need to add something to load the firmware into the dongle??
It appears that the ...utils... added something to the hotplug stuff for the
broadcom chipset, and it should work.  Obviously it isn't.

I thought this was already answered. You must use --enable-bcm203x to
compile the firmware loader. After installation you will see

        /etc/hotplug/usb/bcm203x.usermap
        /etc/hotplug/usb/bcm203x

in the hotplug directories. Maybe your hotplug scripts are too old and
they can't work with extra entries under /etc/hotplug/usb/.

Regards

Marcel




-------------------------------------------------------
SF.Net email is sponsored by Shop4tech.com-Lowest price on Blank Media
100pk Sonic DVD-R 4x for only $29 -100pk Sonic DVD+R for only $33
Save 50% off Retail on Ink & Toner - Free Shipping and Free Gift.
http://www.shop4tech.com/z/Inkjet_Cartridges/9_108_r285
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users