@@ -1,6 +1,16 @@
 # SPDX-License-Identifier: GPL-2.0-only
+
+stm32mp255c-dhcos-dhsbc-overlay-imx219-x10-dtbs := \
+	stm32mp255c-dhcos-dhsbc.dtb \
+	stm32mp255c-dhcos-dhsbc-overlay-imx219-x10.dtbo
+
 dtb-$(CONFIG_ARCH_STM32) += \
 	stm32mp215f-dk.dtb \
 	stm32mp235f-dk.dtb \
+	stm32mp23xx-dhcos-bb.dtb \
+	stm32mp25xx-dhcos-bb.dtb \
+	stm32mp255c-dhcos-dhsbc.dtb \
+	stm32mp255c-dhcos-dhsbc-overlay-imx219-x10.dtb \
+	stm32mp255c-dhcos-dhsbc-overlay-imx219-x10.dtbo \
 	stm32mp257f-dk.dtb \
 	stm32mp257f-ev1.dtb

@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2026 Marek Vasut <marex@nabladev.com>
+ */
+
+/ {
+};

@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2026 Marek Vasut <marex@nabladev.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp235.dtsi"
+#include "stm32mp23xc.dtsi"
+#include "stm32mp23xx-dhcos-som.dtsi"
+
+/ {
+	model = "DH electronics STM32MP23xx DHCOS Breakout Board";
+	compatible = "dh,stm32mp231a-dhcos-bb", "dh,stm32mp231a-dhcos-som", "st,stm32mp231";
+};

@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) 2025-2026 Marek Vasut <marex@nabladev.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxak-pinctrl.dtsi"
+#include "stm32mp2xxx-dhcos-som.dtsi"
+
+/ {
+	model = "DH electronics STM32MP23xx DHCOS SoM";
+	compatible = "dh,stm32mp231a-dhcos-som", "st,stm32mp231";
+
+	aliases {
+		serial1 = &usart1;
+		serial2 = &usart2;
+	};
+};
+
+&rv3032 {
+	interrupts-extended = <&gpiod 10 IRQ_TYPE_EDGE_FALLING>;
+};
+
+/* Bluetooth */
+&usart1 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart1_pins_a>;
+	pinctrl-1 = <&usart1_sleep_pins_a>;
+	pinctrl-2 = <&usart1_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "infineon,cyw55572-bt";
+		brcm,requires-autobaud-mode;
+		max-speed = <3000000>;
+		shutdown-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usart2 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart2_pins_b>;
+	pinctrl-1 = <&usart2_sleep_pins_b>;
+	pinctrl-2 = <&usart2_idle_pins_b>;
+	uart-has-rtscts;
+	status = "okay";
+};

@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2026 Marek Vasut <marex@nabladev.com>
+ *
+ * Set up pipeline for raw bayer capture:
+ * $ media-ctl -d platform:48030000.dcmipp -r
+ * $ media-ctl -d platform:48030000.dcmipp -l '"48020000.csi":1->"dcmipp_input":0[1]'
+ * $ media-ctl -d platform:48030000.dcmipp -l "'dcmipp_input':1->'dcmipp_dump_postproc':0[1]"
+ * $ media-ctl -d platform:48030000.dcmipp --set-v4l2 "'imx219 0-0010':0[fmt:SRGGB8_1X8/1920x1080]"
+ * $ media-ctl -d platform:48030000.dcmipp --set-v4l2 "'48020000.csi':1[fmt:SRGGB8_1X8/1920x1080]"
+ * $ media-ctl -d platform:48030000.dcmipp --set-v4l2 "'dcmipp_input':1[fmt:SRGGB8_1X8/1920x1080 field:none]"
+ * $ media-ctl -d platform:48030000.dcmipp --set-v4l2 "'dcmipp_dump_postproc':0[compose:(0,0)/1920x1080]"
+ * $ media-ctl -d platform:48030000.dcmipp --set-v4l2 "'dcmipp_dump_postproc':1[fmt:SRGGB8_1X8/1920x1080]"
+ * $ v4l2-ctl -d /dev/video0 --set-fmt-video=width=1920,height=1080,pixelformat=RGGB
+ *
+ * Capture frame using v4l2-ctl:
+ * $ v4l2-ctl -d /dev/video0 --stream-mmap --stream-count=1 --stream-to=/frame.raw
+ *
+ * Capture frame using gstreamer:
+ * $ gst-launch-1.0 v4l2src device=/dev/video0 num-buffers=1 ! \
+ *                  video/x-bayer,width=1920,height=1080,format=rggb ! \
+ *                  bayer2rgb ! jpegenc ! filesink location=/test.jpg
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+&{/} {
+	clk_cam_x10: clk-cam-j1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	/* Page 29 / CSI_IF_CN / J1 */
+	reg_cam_x10: reg-cam-j1 {
+		compatible = "regulator-fixed";
+		regulator-name = "cam-X10";
+		enable-active-high;
+		gpios = <&ioexp 13 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&csi {
+	vdd-supply = <&scmi_vddcore>;
+	vdda18-supply = <&scmi_v1v8>;
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi_sink: endpoint {
+				remote-endpoint = <&imx219_x10_out>;
+				data-lanes = <1 2>;
+				bus-type = <4>;
+			};
+		};
+		port@1 {
+			reg = <1>;
+
+			csi_source: endpoint {
+				remote-endpoint = <&dcmipp_0>;
+			};
+		};
+	};
+};
+
+&dcmipp {
+	status = "okay";
+
+	port {
+		dcmipp_0: endpoint {
+			remote-endpoint = <&csi_source>;
+			bus-type = <4>;
+		};
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	cam@10 {
+		compatible = "sony,imx219";
+		reg = <0x10>;
+
+		clocks = <&clk_cam_x10>;
+
+		VANA-supply = <&reg_cam_x10>;
+		VDIG-supply = <&reg_cam_x10>;
+		VDDL-supply = <&reg_cam_x10>;
+
+		orientation = <2>;
+		rotation = <0>;
+
+		port {
+			imx219_x10_out: endpoint {
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <456000000>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi_sink>;
+			};
+		};
+	};
+};

@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2025-2026 Marek Vasut <marex@nabladev.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp255.dtsi"
+#include "stm32mp25xc.dtsi"
+#include "stm32mp25xx-dhcos-som.dtsi"
+
+/ {
+	model = "DH electronics STM32MP255C DHCOS DHSBC";
+	compatible = "dh,stm32mp255c-dhcos-dhsbc", "dh,stm32mp255c-dhcos-som", "st,stm32mp255";
+
+	aliases {
+		ethernet0 = &ethernet1;
+		ethernet1 = &ethernet2;
+	};
+};
+
+&ethernet1 {
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth1_mdio_pins_a &eth1_rgmii_pins_a>;
+	pinctrl-1 = <&eth1_mdio_sleep_pins_a &eth1_rgmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy1: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpioc>;
+			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			realtek,clkout-disable;
+			realtek,clkout-ssc-enable;
+			realtek,rxc-ssc-enable;
+			realtek,sysclk-ssc-enable;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&ioexp 1 GPIO_ACTIVE_LOW>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					color = <LED_COLOR_ID_GREEN>;
+					function = LED_FUNCTION_WAN;
+					linux,default-trigger = "netdev";
+				};
+
+				led@1 {
+					reg = <1>;
+					color = <LED_COLOR_ID_YELLOW>;
+					function = LED_FUNCTION_WAN;
+					linux,default-trigger = "netdev";
+				};
+			};
+		};
+	};
+};
+
+&ethernet2 {
+	phy-handle = <&ethphy2>;
+	phy-mode = "rgmii-id";
+	pinctrl-0 = <&eth2_mdio_pins_a &eth2_rgmii_pins_b>;
+	pinctrl-1 = <&eth2_mdio_sleep_pins_a &eth2_rgmii_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+	st,ext-phyclk;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		ethphy2: ethernet-phy@1 {
+			/* RTL8211F */
+			compatible = "ethernet-phy-id001c.c916";
+			interrupt-parent = <&gpiog>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+			reg = <1>;
+			realtek,clkout-disable;
+			realtek,clkout-ssc-enable;
+			realtek,rxc-ssc-enable;
+			realtek,sysclk-ssc-enable;
+			reset-assert-us = <15000>;
+			reset-deassert-us = <55000>;
+			reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					color = <LED_COLOR_ID_GREEN>;
+					function = LED_FUNCTION_LAN;
+					linux,default-trigger = "netdev";
+				};
+
+				led@1 {
+					reg = <1>;
+					color = <LED_COLOR_ID_YELLOW>;
+					function = LED_FUNCTION_LAN;
+					linux,default-trigger = "netdev";
+				};
+			};
+		};
+	};
+};
+
+&gpioa {
+	gpio-line-names = "DHSBC_HW-CODE_0", "DHSBC_HW-CODE_1", "DHSBC_HW-CODE_2", "",
+			  "DHCOS-E", "DHCOS-J", "", "",
+			  "DHCOS-D", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c2_pins_a>;
+	pinctrl-1 = <&i2c2_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <57>;
+	i2c-scl-falling-time-ns = <7>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&scmi_vddio1 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-settling-time-up-us = <1000>;
+	regulator-settling-time-down-us = <100000>;
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_b>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&ioexp 8 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&scmi_v3v3>;
+	vqmmc-supply = <&scmi_vddio1>;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-ddr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi1_pins_a>;
+	pinctrl-1 = <&spi1_sleep_pins_a>;
+	cs-gpios = <&gpioh 3 0>;
+	status = "okay";
+
+	st33htph: tpm@0 {
+		compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
+		reg = <0>;
+		interrupt-parent = <&gpioa>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioh 2 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <24000000>;
+	};
+};
+
+&spi8 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi8_pins_b>;
+	pinctrl-1 = <&spi8_sleep_pins_b>;
+	cs-gpios = <&gpioz 6 0>;
+};

@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2026 Marek Vasut <marex@nabladev.com>
+ */
+
+/ {
+};

@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
+/*
+ * Copyright (C) 2025-2026 Marek Vasut <marex@nabladev.com>
+ */
+
+/dts-v1/;
+
+#include "stm32mp255.dtsi"
+#include "stm32mp25xc.dtsi"
+#include "stm32mp25xx-dhcos-som.dtsi"
+
+/ {
+	model = "DH electronics STM32MP25xx DHCOS Breakout Board";
+	compatible = "dh,stm32mp251a-dhcos-bb", "dh,stm32mp251a-dhcos-som", "st,stm32mp251";
+};

@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) 2025-2026 Marek Vasut <marex@nabladev.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "stm32mp25-pinctrl.dtsi"
+#include "stm32mp25xxak-pinctrl.dtsi"
+#include "stm32mp2xxx-dhcos-som.dtsi"
+
+/ {
+	model = "DH electronics STM32MP25xx DHCOS SoM";
+	compatible = "dh,stm32mp251a-dhcos-som", "st,stm32mp251";
+
+	aliases {
+		serial1 = &uart8;
+		serial2 = &uart9;
+	};
+};
+
+&rv3032 {
+	interrupts-extended = <&gpioi 10 IRQ_TYPE_EDGE_FALLING>;
+};
+
+/* Bluetooth */
+&uart8 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart8_pins_a>;
+	pinctrl-1 = <&uart8_sleep_pins_a>;
+	pinctrl-2 = <&uart8_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "infineon,cyw55572-bt";
+		brcm,requires-autobaud-mode;
+		max-speed = <3000000>;
+		shutdown-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart9 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart9_pins_a>;
+	pinctrl-1 = <&uart9_sleep_pins_a>;
+	pinctrl-2 = <&uart9_idle_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};

@@ -0,0 +1,442 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause)
+/*
+ * Copyright (C) 2025-2026 Marek Vasut <marex@nabladev.com>
+ */
+
+/ {
+	aliases {
+		mmc0 = &sdmmc2;
+		mmc1 = &sdmmc3;
+		serial0 = &usart6;
+		serial1 = &uart8;
+		eeprom0 = &eeprom0;
+		eeprom0wl = &eeprom0wl;
+		rtc0 = &rv3032;
+		rtc1 = &rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x1 0x0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* Internal RAM reserved memory declaration */
+		tfa_bl31: tfa-bl31@a000000 {
+			reg = <0x0 0xa000000 0x0 0x20000>;
+			no-map;
+		};
+
+		hpdma1_lli: hpdma1-lli@a020000 {
+			reg = <0x0 0xa020000 0x0 0xf0f0>;
+			no-map;
+		};
+
+		hpdma2_lli: hpdma2-lli@a02f0f0 {
+			reg = <0x0 0xa02f0f0 0x0 0xf0f0>;
+			no-map;
+		};
+
+		hpdma3_lli: hpdma3-lli@a03e1e0 {
+			reg = <0x0 0xa03e1e0 0x0 0x1e20>;
+			no-map;
+		};
+
+		bsec_mirror: bsec-mirror@a040000 {
+			reg = <0x0 0xa040000 0x0 0x1000>;
+			no-map;
+		};
+
+		scmi_cid2_s: scmi-cid2-s@a041000 {
+			reg = <0x0 0xa041000 0x0 0x1000>;
+			no-map;
+		};
+
+		scmi_cid2_ns: scmi-cid2-ns@a042000 {
+			reg = <0x0 0xa042000 0x0 0x1000>;
+			no-map;
+		};
+
+		cm33_sram1: cm33-sram1@a043000 {
+			reg = <0x0 0xa043000 0x0 0x1d000>;
+			no-map;
+		};
+
+		cm33_sram2: cm33-sram2@a060000 {
+			reg = <0x0 0xa060000 0x0 0x20000>;
+			no-map;
+		};
+
+		cm33_retram: cm33-retram@a080000 {
+			reg = <0x0 0xa080000 0x0 0x1f000>;
+			no-map;
+		};
+
+		ddr_param: ddr-param@a09f000 {
+			reg = <0x0 0xa09f000 0x0 0x1000>;
+			no-map;
+		};
+
+		cm0_cube_fw: cm0-cube-fw@200C0000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x200C0000 0x0 0x4000>;
+			no-map;
+		};
+
+		cm0_cube_data: cm0-cube-data@200C4000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x200C4000 0x0 0x2000>;
+			no-map;
+		};
+
+		ipc_shmem_2: ipc-shmem-2@200C6000{
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x200C6000 0x0 0x2000>;
+			no-map;
+		};
+
+		/* Backup RAM reserved memory declaration */
+		bl31_lowpower: bl31-lowpower@42000000 {
+			reg = <0x0 0x42000000 0x0 0x1000>;
+			no-map;
+		};
+
+		tfm_its: tfm-its@42001000 {
+			reg = <0x0 0x42001000 0x0 0x1000>;
+			no-map;
+		};
+
+		/* Octo Memory Manager reserved memory declaration */
+		mm_ospi1: mm-ospi@60000000 {
+			reg = <0x0 0x60000000 0x0 0x10000000>;
+			no-map;
+		};
+
+		/* DDR reserved memory declaration */
+		tfm_code: tfm-code@80000000 {
+			reg = <0x0 0x80000000 0x0 0x100000>;
+			no-map;
+		};
+
+		cm33_cube_fw: cm33-cube-fw@80100000 {
+			reg = <0x0 0x80100000 0x0 0x800000>;
+			no-map;
+		};
+
+		tfm_data: tfm-data@80900000 {
+			reg = <0x0 0x80900000 0x0 0x100000>;
+			no-map;
+		};
+
+		cm33_cube_data: cm33-cube-data@80a00000 {
+			reg = <0x0 0x80a00000 0x0 0x800000>;
+			no-map;
+		};
+
+		ipc_shmem_1: ipc-shmem-1@81200000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x81200000 0x0 0xf8000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@812f8000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x812f8000 0x0 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@812f9000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x812f9000 0x0 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@812fa000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x812fa000 0x0 0x6000>;
+			no-map;
+		};
+
+		spare1: spare1@81300000 {
+			reg = <0x0 0x81300000 0x0 0xcc0000>;
+			no-map;
+		};
+
+		bl31_context: bl31-context@81fc0000 {
+			reg = <0x0 0x81fc0000 0x0 0x40000>;
+			no-map;
+		};
+
+		op_tee: op-tee@82000000 {
+			reg = <0x0 0x82000000 0x0 0x2000000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu-reserved@fa800000 {
+			reg = <0x0 0xfa800000 0x0 0x4000000>;
+			no-map;
+		};
+
+		ltdc_sec_layer: ltdc-sec-layer@fe800000 {
+			reg = <0x0 0xfe800000 0x0 0x800000>;
+			no-map;
+		};
+
+		ltdc_sec_rotation: ltdc-sec-rotation@ff000000 {
+			reg = <0x0 0xff000000 0x0 0x1000000>;
+			no-map;
+		};
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			alloc-ranges = <0 0x80000000 0 0x80000000>;
+			size = <0x0 0x8000000>;
+			alignment = <0x0 0x2000>;
+			linux,cma-default;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		post-power-on-delay-ms = <50>;
+		reset-gpios = <&ioexp 3 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&arm_wdt {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&gpioa {
+	gpio-line-names = "", "DHCOS-M", "DHCOS-K", "DHCOS-L",
+			  "DHCOS-E", "DHCOS-J", "", "",
+			  "DHCOS-D", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiof {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "DHCOS_RAM-CODE_2";
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "DHCOS_RAM-CODE_0", "DHCOS_RAM-CODE_1", "",
+			  "", "", "DHCOS-F", "DHCOS_HW-CODE_0";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "DHCOS-I", "DHCOS-N",
+			  "", "", "DHCOS-O", "DHCOS-H",
+			  "DHCOS-G", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioi {
+	gpio-line-names = "DHCOS_HW-CODE_1", "DHCOS_HW-CODE_2", "", "",
+			  "", "", "", "",
+			  "", "DHCOS-C", "", "",
+			  "", "", "", "";
+};
+
+&gpioz {
+	gpio-line-names = "", "", "DHCOS-A", "DHCOS-B",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&i2c8 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c8_pins_b>;
+	pinctrl-1 = <&i2c8_sleep_pins_b>;
+	i2c-scl-rising-time-ns = <57>;
+	i2c-scl-falling-time-ns = <7>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ioexp: gpio@20 {
+		compatible = "kinetic,kts1622", "ti,tcal6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupts-extended = <&gpiod 11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		wakeup-source;
+
+		gpio-line-names =
+			"#ETH1_RST_P0_0", "#ETH0_RST_P0_1",
+			"BT_REG_ON_P0_2", "WL_REG_ON_P0_3",
+			"USB1_PWR_EN_P0_4", "USB1_PWR_STAT_P0_5",
+			"USB0_PWR_EN_P0_6", "USB0_PWR_STAT_P0_7",
+			"SDIO0_CD_P1_0", "USB0_SS_SEL_P1_1",
+			"#PCIe_RST_1_2", "#PCIe_Wake_P1_3",
+			"#QSPI_RST_P1_4", "#CSI0_PWDN_P1_5",
+			"#CSI0_RST_P1_6", "#ETH3_RST_P1_7";
+	};
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c256";	/* ST M24256 */
+		reg = <0x50>;
+		pagesize = <64>;
+	};
+
+	rv3032: rtc@51 {
+		compatible = "microcrystal,rv3032";
+		reg = <0x51>;
+		wakeup-source;
+	};
+
+	eeprom0wl: eeprom@58 {
+		compatible = "st,24256e-wl";	/* ST M24256E WL page of 0x50 */
+		pagesize = <64>;
+		reg = <0x58>;
+	};
+};
+
+&ommanager {
+	memory-region = <&mm_ospi1>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ospi_port1_clk_pins_a
+		     &ospi_port1_io03_pins_a
+		     &ospi_port1_cs0_pins_a>;
+	pinctrl-1 = <&ospi_port1_clk_sleep_pins_a
+		     &ospi_port1_io03_sleep_pins_a
+		     &ospi_port1_cs0_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+};
+
+&ospi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	memory-region = <&mm_ospi1>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		spi-max-frequency = <100000000>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&scmi_regu {
+	scmi_vddcore: regulator@b {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK2>;
+		regulator-name = "vddcore";
+	};
+
+	regulator@c {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK3>;
+		regulator-name = "vddgpu";
+		regulator-always-on;
+	};
+
+	scmi_v1v8: regulator@e {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK5>;
+		regulator-name = "v1v8";
+		regulator-always-on;
+	};
+
+	scmi_v3v3: regulator@10 {
+		reg = <VOLTD_SCMI_STPMIC2_BUCK7>;
+		regulator-name = "v3v3";
+		regulator-always-on;
+	};
+
+	scmi_vdd_emmc: regulator@12 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO2>;
+		regulator-name = "vdd_emmc";
+	};
+
+	scmi_vdd3v3_usb: regulator@14 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO4>;
+		regulator-name = "vdd3v3_usb";
+	};
+
+	scmi_vdd_sdcard: regulator@17 {
+		reg = <VOLTD_SCMI_STPMIC2_LDO7>;
+		regulator-name = "vdd_sdcard";
+	};
+};
+
+&scmi_vddio3 {
+	regulator-always-on;
+};
+
+&scmi_vddio4 {
+	regulator-always-on;
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&scmi_vdd_emmc>;
+	vqmmc-supply = <&scmi_vddio2>;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	no-sd;
+	no-mmc;
+	st,neg-edge;
+	vmmc-supply = <&scmi_v3v3>;
+	vqmmc-supply = <&scmi_v1v8>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	brcmf: wifi@1 {	/* muRata 2FY */
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&usart6 {
+	pinctrl-names = "default", "idle", "sleep";
+	pinctrl-0 = <&usart6_pins_b>;
+	pinctrl-1 = <&usart6_idle_pins_b>;
+	pinctrl-2 = <&usart6_sleep_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};