Re: [PATCH v5 3/4] firmware: psci: Read and use vendor reset types

On 8/9/2024 10:28 PM, Elliot Berman wrote:

On Fri, Aug 09, 2024 at 03:30:38PM +0200, Lorenzo Pieralisi wrote:

quoted

On Wed, Aug 07, 2024 at 11:10:50AM -0700, Elliot Berman wrote:

[...]

quoted

quoted

quoted

+static void psci_vendor_sys_reset2(unsigned long action, void *data)

'action' is unused and therefore it is not really needed.

quoted

+{
+	const char *cmd = data;
+	unsigned long ret;
+	size_t i;
+
+	for (i = 0; i < num_psci_reset_params; i++) {
+		if (!strcmp(psci_reset_params[i].mode, cmd)) {
+			ret = invoke_psci_fn(PSCI_FN_NATIVE(1_1, SYSTEM_RESET2),
+					     psci_reset_params[i].reset_type,
+					     psci_reset_params[i].cookie, 0);
+			pr_err("failed to perform reset \"%s\": %ld\n",
+				cmd, (long)ret);
+		}
+	}
+}
+
 static int psci_sys_reset(struct notifier_block *nb, unsigned long action,
 			  void *data)
 {
+	if (data && num_psci_reset_params)

So, reboot_mode here is basically ignored; if there is a vendor defined
reset, we fire it off.

I think Mark mentioned his concerns earlier related to REBOOT_* mode and
reset type (granted, the context was different):

https://lore.kernel.org/all/20200320120105.GA36658@C02TD0UTHF1T.local/ (local)

I would like to understand if this is the right thing to do before
accepting this patchset.

I don't have any concerns to move this part below checking reboot_mode.
Or, I could add reboot_mode == REBOOT_COLD check.

The question is how can we map vendor specific reboot magic to Linux
reboot modes sensibly in generic PSCI code - that's by definition
vendor specific.

I don't think it's a reasonable thing to do. "reboot bootloader" or
"reboot edl" don't make sense to the Linux reboot modes.

I believe the Linux reboot modes enum is oriented to perspective of
Linux itself and the vendor resets are oriented towards behavior of the
SoC.

Thanks,
Elliot

Agree.

from perspective of linux reboot modes, kernel's current implementation in reset path is like:
__
#1 If reboot_mode is WARM/SOFT and PSCI_SYSRESET2 is supported 
    Call PSCI - SYSTEM_RESET2 - ARCH RESET
#2 ELSE
    Call PSCI - SYSTEM_RESET COLD RESET
___

ARM SPECS for PSCI SYSTEM_RESET2
This function extends SYSTEM_RESET. It provides:
• ARCH RESET: set Bit[31] to 0               = > This is already in place in condition #1.
• vendor-specific resets: set Bit[31] to 1.  = > current patchset adds this part before kernel's reboot_mode reset at #0.


In current patchset, we see a condition added at #0-psci_vendor_reset2 being called before kernel’s current reboot_mode condition and it can take any action only if all below conditions are satisfied.
- PSCI SYSTEM_RESET2 is supported.
- psci dt node defines an entry "bootloader" as a reboot-modes.
- User issues reboot with a command say - (reboot bootloader).
- If vendor reset fails, default reboot mode will execute as is.

Don't see if we will skip or break the kernel reboot_mode flow with this patch. 
Also if user issues reboot <cmd> and <cmd> is supported on SOC vendor reset psci node, should cmd take precedence over kernel reboot mode enum? may be yes?