Re: [PATCH v5 04/11] media: bcm2835-unicam: Add support for CCP2/CSI2 camera interface
From: Sakari Ailus <sakari.ailus@iki.fi>
Date: 2023-07-02 18:18:40
Also in:
linux-devicetree, linux-media, lkml
Hi Laurent, On Sun, Jul 02, 2023 at 06:23:56PM +0300, Laurent Pinchart wrote:
Hi Sakari, On Fri, Feb 25, 2022 at 11:29:18AM +0200, Sakari Ailus wrote:quoted
On Tue, Feb 08, 2022 at 04:50:20PM +0100, Jean-Michel Hautbois wrote:quoted
Add driver for the Unicam camera receiver block on BCM283x processors. It is represented as two video device nodes: unicam-image and unicam-embedded which are connected to an internal subdev (named unicam-subdev) in order to manage streams routing. Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Naushir Patuck <redacted> Signed-off-by: Jean-Michel Hautbois <redacted> --- v4: - Add the vendor prefox for DT name - Use the reg-names in DT parsing - Remove MAINTAINERS entry v3 main changes: - Change code organization - Remove unused variables - Correct the fmt_meta functions - Rewrite the start/stop streaming - You can now start the image node alone, but not the metadata one - The buffers are allocated per-node - only the required stream is started, if the route exists and is enabled - Prefix the macros with UNICAM_ to not have too generic names - Drop colorspace support -> This is causing issues in the try-fmt v4l2-compliance test test VIDIOC_G_FMT: OK fail: v4l2-test-formats.cpp(363): colorspace >= 0xff fail: v4l2-test-formats.cpp(465): testColorspace(!node->is_io_mc, pix.pixelformat, pix.colorspace, pix.ycbcr_enc, pix.quantization) test VIDIOC_TRY_FMT: FAIL fail: v4l2-test-formats.cpp(363): colorspace >= 0xff fail: v4l2-test-formats.cpp(465): testColorspace(!node->is_io_mc, pix.pixelformat, pix.colorspace, pix.ycbcr_enc, pix.quantization) test VIDIOC_S_FMT: FAIL v2: Remove the unicam_{info,debug,error} macros and use dev_dbg/dev_err instead. --- drivers/media/platform/Kconfig | 1 + drivers/media/platform/Makefile | 2 + drivers/media/platform/bcm2835/Kconfig | 21 + drivers/media/platform/bcm2835/Makefile | 3 + .../platform/bcm2835/bcm2835-unicam-regs.h | 253 ++ .../media/platform/bcm2835/bcm2835-unicam.c | 2570 +++++++++++++++++ 6 files changed, 2850 insertions(+) create mode 100644 drivers/media/platform/bcm2835/Kconfig create mode 100644 drivers/media/platform/bcm2835/Makefile create mode 100644 drivers/media/platform/bcm2835/bcm2835-unicam-regs.h create mode 100644 drivers/media/platform/bcm2835/bcm2835-unicam.c[snip]quoted
quoted
diff --git a/drivers/media/platform/bcm2835/bcm2835-unicam-regs.h b/drivers/media/platform/bcm2835/bcm2835-unicam-regs.h new file mode 100644 index 000000000000..b8d297076a02 --- /dev/null +++ b/drivers/media/platform/bcm2835/bcm2835-unicam-regs.h[snip]quoted
quoted
+static int unicam_connect_of_subdevs(struct unicam_device *unicam) +{ + struct v4l2_fwnode_endpoint ep = { }; + struct fwnode_handle *ep_handle; + struct v4l2_async_subdev *asd; + unsigned int lane; + int ret = -EINVAL; + + if (of_property_read_u32(unicam->dev->of_node, "brcm,num-data-lanes", + &unicam->max_data_lanes) < 0) {As you're already using fwnode API below, you could use device_property_read_u32() here. You can then replace of_device.h by mod_devicetable.h. Up to you.quoted
+ dev_err(unicam->dev, "DT property %s not set\n", + "brcm,num-data-lanes"); + return -EINVAL; + } + + /* Get the local endpoint and remote device. */ + ep_handle = fwnode_graph_get_endpoint_by_id(dev_fwnode(unicam->dev), + 0, 0, + FWNODE_GRAPH_ENDPOINT_NEXT); + if (!ep_handle) { + dev_err(unicam->dev, "No endpoint\n"); + return -ENODEV; + } + + /* Parse the local endpoint and validate its configuration. */ + if (v4l2_fwnode_endpoint_alloc_parse(ep_handle, &ep)) {As you don't need link-frequencies property parsing, you should use v4l2_fwnode_endpoint_parse(). That avoids having to call v4l2_fwnode_endpoint_free().quoted
+ dev_err(unicam->dev, "could not parse endpoint\n"); + goto cleanup_exit; + } + + dev_dbg(unicam->dev, "parsed local endpoint, bus_type %u\n", + ep.bus_type); + + unicam->bus_type = ep.bus_type; + + switch (ep.bus_type) { + case V4L2_MBUS_CSI2_DPHY: + switch (ep.bus.mipi_csi2.num_data_lanes) { + case 1: + case 2: + case 4: + break; + + default: + dev_err(unicam->dev, "%u data lanes not supported\n", + ep.bus.mipi_csi2.num_data_lanes); + goto cleanup_exit; + } + + for (lane = 0; lane < ep.bus.mipi_csi2.num_data_lanes; lane++) { + if (ep.bus.mipi_csi2.data_lanes[lane] != lane + 1) { + dev_err(unicam->dev, "data lanes reordering not supported\n"); + goto cleanup_exit; + } + } + + if (ep.bus.mipi_csi2.num_data_lanes > unicam->max_data_lanes) { + dev_err(unicam->dev, "endpoint requires %u data lanes when %u are supported\n", + ep.bus.mipi_csi2.num_data_lanes, + unicam->max_data_lanes); + } + + unicam->active_data_lanes = ep.bus.mipi_csi2.num_data_lanes; + unicam->bus_flags = ep.bus.mipi_csi2.flags; + + break; + + case V4L2_MBUS_CCP2: + if (ep.bus.mipi_csi1.clock_lane != 0 || + ep.bus.mipi_csi1.data_lane != 1) { + dev_err(unicam->dev, "unsupported lanes configuration\n");If the hardware doesn't support lane remapping for CCP2, then that should be reflected in DT bindings, i.e. data-lanes isn't relevant. There's no need to check that here.Should the above check for CSI-2 be dropped as well then ?
Same for CSI-2, too: if there's nothing to configure there (lane remapping) there's no need to validate that part of the DT either.
quoted
quoted
+ goto cleanup_exit; + } + + unicam->max_data_lanes = 1; + unicam->active_data_lanes = 1; + unicam->bus_flags = ep.bus.mipi_csi1.strobe; + break; + + default: + /* Unsupported bus type */ + dev_err(unicam->dev, "unsupported bus type %u\n", + ep.bus_type); + goto cleanup_exit; + } + + dev_dbg(unicam->dev, "%s bus, %u data lanes, flags=0x%08x\n", + unicam->bus_type == V4L2_MBUS_CSI2_DPHY ? "CSI-2" : "CCP2", + unicam->active_data_lanes, unicam->bus_flags);V4l2-fwnode already prints this information I believe.True. It does so with pr_debug() though, it would be nice to use dev_dbg(). That's a candidate for a separate fix of course.
The reason for using pr_debug() is that the device isn't used by the fwnode framework. Would you add that just for debug prints? Note that the device nodes themselves are already being printed so it adds little to the usefulness of the messages. -- Kind regards, Sakari Ailus _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel