On Tue 14 Dec 2021 at 10:21, Qianggui Song [off-list ref] wrote:
Add new pinctrl driver for Amlogic's Meson-S4 SoC which share the
same register laytout as the previous Meson-A1.
Signed-off-by: Qianggui Song <redacted>
---
[...]
quoted hunk ↗ jump to hunk
+
+/* Bank D func1 */
+static const unsigned int uart_b_tx_d_pins[] = { GPIOD_0 };
+static const unsigned int uart_b_rx_d_pins[] = { GPIOD_1 };
+static const unsigned int uart_b_cts_d_pins[] = { GPIOD_2 };
+static const unsigned int uart_b_rts_d_pins[] = { GPIOD_3 };
Your S805x2 documenation says the 4 pins above are HDMI related for func 1
+static const unsigned int remote_out_pins[] = { GPIOD_4 };
+static const unsigned int remote_in_pins[] = { GPIOD_5 };
SPDIF for those 2
quoted hunk ↗ jump to hunk
+static const unsigned int jtag_1_clk_pins[] = { GPIOD_6 };
+static const unsigned int jtag_1_tms_pins[] = { GPIOD_7 };
+static const unsigned int jtag_1_tdi_pins[] = { GPIOD_8 };
+static const unsigned int jtag_1_tdo_pins[] = { GPIOD_9 };
I2C for those 4
It goes on like this for the rest of GPIO Bank D and I did not check the
other banks
Could you please clarify
* Does the S4 applies to S805X2, S905Y4, Both ?
* Is the S805X2 Datasheet Revision 0.4 accurate ?
quoted hunk ↗ jump to hunk
+static const unsigned int clk12_24_pins[] = { GPIOD_10 };
+static const unsigned int pwm_g_hiz_pins[] = { GPIOD_11 };
+
[...]
quoted hunk ↗ jump to hunk
+
+static const char * const tdm_groups[] = {
+ "tdm_d2_c", "tdm_d3_c", "tdm_fs1_c", "tdm_d4_c", "tdm_d5_c",
+ "tdm_fs1_d", "tdm_d4_d", "tdm_d3_d", "tdm_d2_d", "tdm_sclk1_d",
+ "tdm_sclk1_h", "tdm_fs1_h", "tdm_d2_h", "tdm_d3_h", "tdm_d4_h",
+ "tdm_d1", "tdm_d0", "tdm_fs0", "tdm_sclk0", "tdm_fs2", "tdm_sclk2",
+ "tdm_d4_z", "tdm_d5_z", "tdm_d6", "tdm_d7"
+};
On previous chip, there were pin assigned to tdm A, B or C.
On this generation, it seems you have added a second level on pinmuxing
to re-route the audio pins to different controllers
In such case, I don't think they belong in the same group.
Depending on settins, D2 and D3 could be unrelated
I think each audio pin should have its own group (one group for D3, one
D4, etc ...)
quoted hunk ↗ jump to hunk
+
+static const char * const mclk_groups[] = {
+ "mclk_1_c", "mclk_1_d", "mclk_1_h", "mclk_2"
+
+};
mclk_1 and mclk_2 should be in separate groups
quoted hunk ↗ jump to hunk
+
+static const char * const remote_out_groups[] = {
+ "remote_out"
+};
+
+static const char * const remote_in_groups[] = {
+ "remote_in"
+};
+
+static const char * const clk12_24_groups[] = {
+ "clk12_24"
+};
+
+static const char * const clk_32k_in_groups[] = {
+ "clk_32k_in"
+};
+
+static const char * const pwm_a_hiz_groups[] = {
+ "pwm_a_hiz"
+};
+
I'm curious to know what the pwm hiz function is ?
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel