RE: [PATCH] drm: xlnx: call pm_runtime_get_sync before setting pixel clock
From: Rohit Visavalia <hidden>
Date: 2021-03-17 11:19:22
Also in:
dri-devel
Hi Quanyang & Laurent, I tested this patch(which moves pm_runtime_get_sync at the very beginning of the function zynqmp_disp_crtc_atomic_enable), i don't see any behavior change with patch, means with patch also DP display is not getting up and it is required to resolution change to make it up. Also valid bit is not getting set for VPLL_FRAC_CFG on bootup, same behavior as without patch. Thanks, Rohit
-----Original Message----- From: Michal Simek <redacted> Sent: Wednesday, March 17, 2021 1:56 PM To: quanyang.wang <redacted>; Laurent Pinchart [off-list ref]; Rohit Visavalia [off-list ref] Cc: Hyun Kwon <redacted>; David Airlie <redacted>; Daniel Vetter [off-list ref]; Michal Simek [off-list ref]; dri- devel@lists.freedesktop.org; linux-arm-kernel@lists.infradead.org; linux- kernel@vger.kernel.org Subject: Re: [PATCH] drm: xlnx: call pm_runtime_get_sync before setting pixel clock +Rohit On 3/17/21 4:00 AM, quanyang.wang wrote:quoted
Hi Laurent, On 3/17/21 4:32 AM, Laurent Pinchart wrote:quoted
Hi Quanyang, Thank you for the patch. On Wed, Mar 10, 2021 at 12:59:45PM +0800,quanyang.wang@windriver.comquoted
quoted
wrote:quoted
From: Quanyang Wang <redacted> The Runtime PM subsystem will force the device "fd4a0000.zynqmp-display"quoted
quoted
quoted
to enter suspend state while booting if the following conditions are met: - the usage counter is zero (pm_runtime_get_sync hasn't been called yet) - no 'active' children (no zynqmp-dp-snd-xx node under dpsub node) - no other device in the same power domain (dpdma node has no "power-domains = <&zynqmp_firmware PD_DP>" property) So there is a scenario as below: 1) DP device enters suspend state <- call zynqmp_gpd_power_off 2) zynqmp_disp_crtc_setup_clock <- configurate register VPLL_FRAC_CFG 3) pm_runtime_get_sync <- call zynqmp_gpd_power_on and clear previous VPLL_FRAC_CFG configuration 4) clk_prepare_enable(disp->pclk) <- enable failed since VPLL_FRAC_CFG configuration is corrupted From above, we can see that pm_runtime_get_sync may clear register VPLL_FRAC_CFG configuration and result the failure of clk enabling. Putting pm_runtime_get_sync at the very beginning of the function zynqmp_disp_crtc_atomic_enable can resolve this issue.Isn't this an issue in the firmware though, which shouldn't clear the previous VPLLF_FRAC_CFG ?Thank you for your review. I used to look into the atf and PWU code and it seems (I didn't add debug code to PMU to make sure if PMU really does this, I only in kernel call zynqmp_pm_get_pll_frac_data to make sure that the value in data field of VPLL_FRAC_CFG register is changed from 0x4000 to 0x0 after run pm_runtime_get_sync) that PMU intends to reset VPLL when there is an Off and On in DP Powerdomain. Linux ATF PWU zynqmp_gpd_power_on ->zynqmp_pm_set_requirement -->send PM_SET_REQUIREMENT to ATF ==> ATF send ipi to PWU ==> PmSetRequirement ->PmRequirementUpdate -->PmUpdateSlave(masterReq->slave) --->PmSlaveChangeState ---->PmSlaveChangeState ----->PmSlaveClearAfterState ------>PmClockRelease ------->PmClockReleaseInt(&ch->clock->base) -------->clk->class->release(clk) --------->PmPllBypassAndReset //Here reset the VPLL then VPLL_FRAC_CFG is cleared.quoted
quoted
Signed-off-by: Quanyang Wang <redacted>Nonetheless, this change looks good to me, I actually had the same patch in my tree while investigation issues related to the clock rate, so Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> I was hoping it would solve the issue I'm experiencing with the DP clock, but that's not the case :-( In a nutshell, when the DP is first started, the clock frequency is incorrect. The following quick & dirty patch fixes the problem:diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.cb/drivers/gpu/drm/xlnx/zynqmp_disp.c index 74ac0a064eb5..fdbe1b0640aa 100644--- a/drivers/gpu/drm/xlnx/zynqmp_disp.c +++ b/drivers/gpu/drm/xlnx/zynqmp_disp.c@@ -1439,6 +1439,10 @@ zynqmp_disp_crtc_atomic_enable(structdrm_crtcquoted
quoted
*crtc, pm_runtime_get_sync(disp->dev); + ret = clk_prepare_enable(disp->pclk); + if (!ret) + clk_disable_unprepare(disp->pclk); + zynqmp_disp_crtc_setup_clock(crtc, adjusted_mode); ret = clk_prepare_enable(disp->pclk); The problem doesn't seem to be in the kernel, but on the TF-A or PMU firmware side. Have you experienced this by any chance ?Yes, I bumped into the same issue and I used to make a patch (Patch 1) as below. I didn't send it to mainline because it seems not to be a driver issue. The mode of VPLL is not set correctly because: 1) VPLL is enabled before linux 2) linux calling pm_clock_set_pll_mode can't really set register because in ATF it only store the mode value to a structure and wait a clk-enable request to do the register-set operation. 3) linux call clk_enable will not send a clk-enable request since it checks that the VPLL is already hardware-enabled because of 1). So the firmware should disable VPLL when it exits and also in linux zynqmp clk driver there should be a check list to reset some clks to a predefined state. By the way, there is a tiny patch (Patch 2) to fix the black screen issue in DP. I think you may be preparing a big patch which add drm properties to this driver and it may contain this modification, so I didn't send it. Thanks, Quanyang Patch 1: From 93311de2c61e87f2426b89259d81cded71aee673 Mon Sep 17 00:00:002001quoted
From: Quanyang Wang <redacted> Date: Thu, 3 Dec 2020 19:19:50 +0800 Subject: [PATCH 1/3] drm: xlnx: set PLL_MODE_FRAC mode to VPLL_FRAC_CFG by re-enabling disp->pclk When the function clk_set_rate configures the rate of disp->pclk, zynqmp_pm_set_pll_frac_mode will be called to set VPLL's mode to be PLL_MODE_FRAC or PLL_MODE_INT by invoking an SMC call to ATF. But in ATF, the service pm_clock_set_pll_mode doesn't really set the VPLL_FRAC_CFG register but only stores the mode value to struct pm_pll *pll. The operation that sets the register must be triggered by zynqmp_pm_clock_enable. Since disp->pclk is enabled in hardware before linux booting, clk_prepare_enable will skip over zynqmp_pm_clock_enable. So we have to enable then disable disp->pclk, and re-enable it to make sure that zynqmp_pm_clock_enable is triggered and the mode is set to VPLL_FRAC_CFG. Or else VPLL will work in an incorrect mode. Signed-off-by: Quanyang Wang <redacted> --- drivers/gpu/drm/xlnx/zynqmp_disp.c | 5 +++++ 1 file changed, 5 insertions(+)diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.cb/drivers/gpu/drm/xlnx/zynqmp_disp.c index 98bd48f13fd1..19753ffc424e 100644--- a/drivers/gpu/drm/xlnx/zynqmp_disp.c +++ b/drivers/gpu/drm/xlnx/zynqmp_disp.c@@ -1668,6 +1668,11 @@ int zynqmp_disp_probe(struct zynqmp_dpsub*dpsub, struct drm_device *drm) dev_err(disp->dev, "failed to init any video clock\n"); return PTR_ERR(disp->pclk); } + + /* Make sure that disp->pclk is disabled in hardware */ + ret = clk_prepare_enable(disp->pclk); + clk_disable_unprepare(disp->pclk); + disp->pclk_from_ps = true; } Patch 2: From 8c6d36bcb4e79e0e5f8e157446cd994b4a2126f0 Mon Sep 17 00:00:002001quoted
From: Quanyang Wang <redacted> Date: Thu, 3 Dec 2020 19:32:56 +0800 Subject: [PATCH 2/3] drm: xlnx: configure alpha value to make graphic layer opaque Since graphics layer is primary, and video layer is overaly, we need to configure the V_BLEND_SET_GLOBAL_ALPHA_REG register to make graphic layer opaque by default, or else graphic layer will be transparent and invisible. Signed-off-by: Quanyang Wang <redacted> --- drivers/gpu/drm/xlnx/zynqmp_disp.c | 3 ++- drivers/gpu/drm/xlnx/zynqmp_disp_regs.h | 1 + 2 files changed, 3 insertions(+), 1 deletion(-)diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.cb/drivers/gpu/drm/xlnx/zynqmp_disp.c index 19753ffc424e..5c84589e1899 100644--- a/drivers/gpu/drm/xlnx/zynqmp_disp.c +++ b/drivers/gpu/drm/xlnx/zynqmp_disp.c@@ -1468,7 +1468,8 @@ zynqmp_disp_crtc_atomic_enable(struct drm_crtc*crtc, zynqmp_disp_blend_set_output_format(&disp->blend, ZYNQMP_DPSUB_FORMAT_RGB); zynqmp_disp_blend_set_bg_color(&disp->blend, 0, 0, 0); - zynqmp_disp_blend_set_global_alpha(&disp->blend, false, 0); + zynqmp_disp_blend_set_global_alpha(&disp->blend, true, + ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX); zynqmp_disp_enable(disp);diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp_regs.hb/drivers/gpu/drm/xlnx/zynqmp_disp_regs.h index f92a006d5070..ef409aca11ad 100644--- a/drivers/gpu/drm/xlnx/zynqmp_disp_regs.h +++ b/drivers/gpu/drm/xlnx/zynqmp_disp_regs.h@@ -22,6 +22,7 @@#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA 0xc #define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_VALUE(n) ((n) << 1) #define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_EN BIT(0) +#define ZYNQMP_DISP_V_BLEND_SET_GLOBAL_ALPHA_MAX 0xff #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT 0x14 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_RGB 0x0 #define ZYNQMP_DISP_V_BLEND_OUTPUT_VID_FMT_YCBCR444 0x1quoted
quoted
--- drivers/gpu/drm/xlnx/zynqmp_disp.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)diff --git a/drivers/gpu/drm/xlnx/zynqmp_disp.cb/drivers/gpu/drm/xlnx/zynqmp_disp.c index 148add0ca1d6..909e6c265406 100644--- a/drivers/gpu/drm/xlnx/zynqmp_disp.c +++ b/drivers/gpu/drm/xlnx/zynqmp_disp.c@@ -1445,9 +1445,10 @@ zynqmp_disp_crtc_atomic_enable(structdrm_crtc *crtc, struct drm_display_mode *adjusted_mode = &crtc->state->adjusted_mode; int ret, vrefresh; + pm_runtime_get_sync(disp->dev); + zynqmp_disp_crtc_setup_clock(crtc, adjusted_mode); - pm_runtime_get_sync(disp->dev); ret = clk_prepare_enable(disp->pclk); if (ret) { dev_err(disp->dev, "failed to enable a pixel clock\n");
_______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel