Hi,

On Tue, Sep 01, 2020 at 01:45:07PM +0900, Chanwoo Choi wrote:

Hi Maxime,

On 7/9/20 2:42 AM, Maxime Ripard wrote:

quoted

The HDMI controllers found in the BCM2711 SoC need some adjustments to the
bindings, especially since the registers have been shuffled around in more
register ranges.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <redacted>
---
 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
 1 file changed, 109 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml

diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml
new file mode 100644
index 000000000000..6091fe3d315b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml

@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: https://protect2.fireeye.com/url?k=556aeb05-08b8fda0-556b604a-0cc47a31bee8-c3a0ebd1d22c3183&q=1&u=http%3A%2F%2Fdevicetree.org%2Fschemas%2Fdisplay%2Fbrcm%2Cbcm2711-hdmi.yaml%23
+$schema: https://protect2.fireeye.com/url?k=24fa660c-792870a9-24fbed43-0cc47a31bee8-0bf16f4fd60f0ab4&q=1&u=http%3A%2F%2Fdevicetree.org%2Fmeta-schemas%2Fcore.yaml%23
+
+title: Broadcom BCM2711 HDMI Controller Device Tree Bindings
+
+maintainers:
+  - Eric Anholt <eric@anholt.net>
+
+properties:
+  compatible:
+    enum:
+      - brcm,bcm2711-hdmi0
+      - brcm,bcm2711-hdmi1
+
+  reg:
+    items:
+      - description: HDMI controller register range
+      - description: DVP register range
+      - description: HDMI PHY register range
+      - description: Rate Manager register range
+      - description: Packet RAM register range
+      - description: Metadata RAM register range
+      - description: CSC register range
+      - description: CEC register range
+      - description: HD register range
+
+  reg-names:
+    items:
+      - const: hdmi
+      - const: dvp
+      - const: phy
+      - const: rm
+      - const: packet
+      - const: metadata
+      - const: csc
+      - const: cec
+      - const: hd
+
+  clocks:
+    description: The HDMI state machine clock

I'm not sure the following description is correct.
But, this description doesn't contain the information of audio clock.

	description: The HDMI state machine and audio clock

quoted

+
+  clock-names:
+    const: hdmi

This patch is missing the following clock information for audio clock.

	const: clk-108M

quoted

+
+  ddc:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/phandle
+    description: >
+      Phandle of the I2C controller used for DDC EDID probing
+
+  hpd-gpios:
+    description: >
+      The GPIO pin for the HDMI hotplug detect (if it doesn't appear
+      as an interrupt/status bit in the HDMI controller itself)
+
+  dmas:
+    maxItems: 1
+    description: >
+      Should contain one entry pointing to the DMA channel used to
+      transfer audio data.
+
+  dma-names:
+    const: audio-rx
+
+  resets:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - resets
+  - ddc
+
+additionalProperties: false
+
+examples:
+  - |
+    hdmi0: hdmi@7ef00700 {
+        compatible = "brcm,bcm2711-hdmi0";
+        reg = <0x7ef00700 0x300>,
+              <0x7ef00300 0x200>,
+              <0x7ef00f00 0x80>,
+              <0x7ef00f80 0x80>,
+              <0x7ef01b00 0x200>,
+              <0x7ef01f00 0x400>,
+              <0x7ef00200 0x80>,
+              <0x7ef04300 0x100>,
+              <0x7ef20000 0x100>;
+        reg-names = "hdmi",
+                    "dvp",
+                    "phy",
+                    "rm",
+                    "packet",
+                    "metadata",
+                    "csc",
+                    "cec",
+                    "hd";
+        clocks = <&firmware_clocks 13>;
+        clock-names = "hdmi";

Also, this example doesn't include the instance of audio clock.
Need to edit them as following:

	clock-names = "hdmi", "clk-108M";
	clocks = <&firmware_clocks 13>, <&dvp 0>;

Indeed, thanks for pointing it out

Maxime