Hi Dan,

quoted

quoted

Sorry for the _noise_ :‑(
This feature seems to be working fine with VRTC drivers.
I have tested this with a pre-compiled image of Archlinux distro.

[root@alarm alarm]# uname -a
Linux alarm 5.7.8-1-ARCH #1 SMP Sun Jul 12 03:38:28 UTC 2020 aarch64 GNU/Linux
[root@alarm alarm]# rtcwake -s 30 -m mem
rtcwake: assuming RTC uses UTC ...
rtcwake: wakeup from "mem" using /dev/rtc0 at Thu Jan  1 00:10:14 1970
[  583.591477] PM: suspend entry (deep)
[  583.593737] Filesystems sync: 0.002 seconds
[  583.818967] Freezing user space processes ... (elapsed 0.005 seconds) done.
[  583.825802] OOM killer disabled.
[  583.828966] Freezing remaining freezable tasks ... (elapsed 0.003
seconds) done.
[  583.880280] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  584.020094] PM: suspend devices took 0.190 seconds
[  584.070586] Disabling non-boot CPUs ...
[  584.075037] CPU1: shutdown
[  584.075223] psci: CPU1 killed (polled 0 ms)
[  584.097199] CPU2: shutdown
[  584.098546] psci: CPU2 killed (polled 0 ms)
[  584.115370] CPU3: shutdown
[  584.116500] psci: CPU3 killed (polled 0 ms)
[  584.128116] CPU4: shutdown
[  584.129235] psci: CPU4 killed (polled 10 ms)
[  584.140122] CPU5: shutdown
[  584.147289] psci: CPU5 killed (polled 0 ms)
bl30 get wakeup sources!
process command 00000006
bl30 enter suspend!
Little core clk suspend rate 1896000000
Big core clk suspend rate 24000000
store restore gp0 pll
suspend_counter: 3
Enter ddr suspend
ddr suspend time: 16us
alarm=31S
process command 00000001
GPIOA_11/13 off
cec ver:2018/04/19
CEC cfg:0x0000
WAKEUP GPIO cfg:0x00000000
use vddee new table!
use vddee new table!
exit_reason:0x03
Enter ddr resume
DMC_DRAM_STAT3: 0x544
ddr resume time: 3188us
store restore gp0 pll
cfg15 33b00000
cfg15 33b00000
Li[  584.148720] Enabling non-boot CPUs ...
[  584.149124] Detected VIPT I-cache on CPU1
[  584.149167] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[  584.149594] CPU1 is up
[  584.160687] Detected VIPT I-cache on CPU2
[  584.160730] arch_timer: CPU2: Trapping CNTVCT access
[  584.160741] CPU2: Booted secondary processor 0x0000000100 [0x410fd092]
[  584.161327] CPU2 is up
[  584.177645] Detected VIPT I-cache on CPU3
[  584.177668] arch_timer: CPU3: Trapping CNTVCT access
[  584.177675] CPU3: Booted secondary processor 0x0000000101 [0x410fd092]
[  584.178036] CPU3 is up
[  584.195338] Detected VIPT I-cache on CPU4
[  584.195361] arch_timer: CPU4: Trapping CNTVCT access
[  584.195368] CPU4: Booted secondary processor 0x0000000102 [0x410fd092]
[  584.195762] CPU4 is up
[  584.213002] Detected VIPT I-cache on CPU5
[  584.213024] arch_timer: CPU5: Trapping CNTVCT access
[  584.213032] CPU5: Booted secondary processor 0x0000000103 [0x410fd092]
[  584.213450] CPU5 is up
ttle core clk resume rate 1896000000
Big core clk resume rate 50000000
[  584.279042] meson8b-dwmac ff3f0000.ethernet eth0: No Safety
Features support found
[  584.281232] meson8b-dwmac ff3f0000.ethernet eth0: configuring for
phy/rgmii link mode
[  584.401216] usb usb1: root hub lost power or was reset
[  584.401470] usb usb2: root hub lost power or was reset
[  584.655446] dwc3-meson-g12a ffe09000.usb: switching to Device Mode
[  584.801108] usb 2-1: reset SuperSpeed Gen 1 USB device number 2
using xhci-hcd
[  584.979632] usb 1-1: reset high-speed USB device number 2 using xhci-hcd
[  585.260450] usb 2-1.1: reset SuperSpeed Gen 1 USB device number 3
using xhci-hcd
[  585.333303] PM: resume devices took 1.100 seconds
[  585.333507] OOM killer enabled.
[  585.335549] Restarting tasks ... done.
[  585.378044] PM: suspend exit
rtcwake: read rtc alarm failed: Invalid argument
[root@alarm alarm]#

-Anand

After confirming that the suspend resume feature is working correctly
I found the solution to the reset warning on 5.8.x kernel
Please can you try this following patch.

$ cat resetwarn.patch

diff --git a/drivers/usb/dwc3/dwc3-meson-g12a.c

b/drivers/usb/dwc3/dwc3-meson-g12a.c
index 1f7f4d88ed9d..60a6f49139fd 100644

--- a/drivers/usb/dwc3/dwc3-meson-g12a.c
+++ b/drivers/usb/dwc3/dwc3-meson-g12a.c

@@ -730,7 +730,7 @@ static int dwc3_meson_g12a_probe(struct

platform_device *pdev)

        platform_set_drvdata(pdev, priv);

-       priv->reset = devm_reset_control_get_shared(dev, NULL);
+       priv->reset = devm_reset_control_get_shared(dev, "dwc3_meson");
        if (IS_ERR(priv->reset)) {
                ret = PTR_ERR(priv->reset);
                dev_err(dev, "failed to get device reset, err=%d\n", ret);

-Anand

Apologize once again above changes break the usb functionality.
the correct fix along with these changes should be as below.
reset controllers need *resets* and *reset-names* to work correctly.

But the _reset controller_ warning continues on suspend / resume features,
I am looking to find a FIX into this issue.

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi

b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 593a006f4b7b..6d34dfa9825c 100644

--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi

@@ -2318,6 +2318,7 @@ usb: usb@ffe09000 {

                        clocks = <&clkc CLKID_USB>;
                        resets = <&reset RESET_USB>;
+                       reset-names = "dwc3_meson";

                        dr_mode = "otg";

-Anand