[PATCH net-next v5 10/11] arm64: dts: ti: k3-j721e-common-proc-board: add mcu cpsw nuss pinmux and phy defs
From: Grygorii Strashko <grygorii.strashko@ti.com>
Date: 2020-03-19 16:29:03
Also in:
linux-devicetree, lkml, netdev
Subsystem:
arm/texas instruments k3 architecture, the rest · Maintainers:
Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Linus Torvalds
The TI J721E EVM base board has TI DP83867 PHY connected to external CPSW NUSS Port 1 in rgmii-rxid mode. Hence, add pinmux and Ethernet PHY configuration for TI j721e SoC MCU Gigabit Ethernet two ports Switch subsystem (CPSW NUSS). Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <redacted> --- .../dts/ti/k3-j721e-common-proc-board.dts | 43 +++++++++++++++++++ 1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 7a5c3d4adadd..98e5e17e3ff7 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts@@ -8,6 +8,7 @@ #include "k3-j721e-som-p0.dtsi" #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> +#include <dt-bindings/net/ti-dp83867.h> / { chosen {
@@ -128,6 +129,30 @@ J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */ >; }; + + mcu_cpsw_pins_default: mcu_cpsw_pins_default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */ + J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */ + J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */ + J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */ + J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */ + J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */ + J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */ + J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */ + J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */ + J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */ + J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */ + J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */ + >; + }; + + mcu_mdio_pins_default: mcu_mdio1_pins_default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */ + J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */ + >; + }; }; &wkup_uart0 {
@@ -429,3 +454,21 @@ #gpio-cells = <2>; }; }; + +&mcu_cpsw { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; +}; + +&davinci_mdio { + phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&phy0>; +};
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel