On 10/09/2019 11:27, Matthias Brugger wrote:

On 09/09/2019 21:33, Stefan Wahren wrote:

quoted

Hi Nicolas,

Am 09.09.19 um 11:58 schrieb Nicolas Saenz Julienne:

quoted

Hi all,
this series attempts to address some issues we found while bringing up
the new Raspberry Pi 4 in arm64 and it's intended to serve as a follow
up of these discussions:
v4: https://lkml.org/lkml/2019/9/6/352
v3: https://lkml.org/lkml/2019/9/2/589
v2: https://lkml.org/lkml/2019/8/20/767
v1: https://lkml.org/lkml/2019/7/31/922
RFC: https://lkml.org/lkml/2019/7/17/476

The new Raspberry Pi 4 has up to 4GB of memory but most peripherals can
only address the first GB: their DMA address range is
0xc0000000-0xfc000000 which is aliased to the first GB of physical
memory 0x00000000-0x3c000000. Note that only some peripherals have these
limitations: the PCIe, V3D, GENET, and 40-bit DMA channels have a wider
view of the address space by virtue of being hooked up trough a second
interconnect.

Part of this is solved on arm32 by setting up the machine specific
'.dma_zone_size = SZ_1G', which takes care of reserving the coherent
memory area at the right spot. That said no buffer bouncing (needed for
dma streaming) is available at the moment, but that's a story for
another series.

Unfortunately there is no such thing as 'dma_zone_size' in arm64. Only
ZONE_DMA32 is created which is interpreted by dma-direct and the arm64
arch code as if all peripherals where be able to address the first 4GB
of memory.

In the light of this, the series implements the following changes:

- Create both DMA zones in arm64, ZONE_DMA will contain the first 1G
  area and ZONE_DMA32 the rest of the 32 bit addressable memory. So far
  the RPi4 is the only arm64 device with such DMA addressing limitations
  so this hardcoded solution was deemed preferable.

- Properly set ARCH_ZONE_DMA_BITS.

- Reserve the CMA area in a place suitable for all peripherals.

This series has been tested on multiple devices both by checking the
zones setup matches the expectations and by double-checking physical
addresses on pages allocated on the three relevant areas GFP_DMA,
GFP_DMA32, GFP_KERNEL:

- On an RPi4 with variations on the ram memory size. But also forcing
  the situation where all three memory zones are nonempty by setting a 3G
  ZONE_DMA32 ceiling on a 4G setup. Both with and without NUMA support.

i like to test this series on Raspberry Pi 4 and i have some questions
to get arm64 running:

Do you use U-Boot? Which tree?

If you want to use U-Boot, try v2019.10-rc4, it should have everything you need
to boot your kernel.

Ok, here is a thing. In the linux kernel we now use bcm2711 as SoC name, but the
RPi4 devicetree provided by the FW uses mostly bcm2838. U-Boot in its default
config uses the devicetree provided by the FW, mostly because this way you don't
have to do anything to find out how many RAM you really have. Secondly because
this will allow us, in the near future, to have one U-boot binary for both RPi3
and RPi4 (and as a side effect one binary for RPi1 and RPi2).

Anyway, I found at least, that the following compatibles need to be added:

"brcm,bcm2838-cprman"
"brcm,bcm2838-gpio"

Without at least the cprman driver update, you won't see anything.

"brcm,bcm2838-rng200" is also a candidate.

I also suppose we will need to add "brcm,bcm2838" to
arch/arm/mach-bcm/bcm2711.c, but I haven't verified this.

Regards,
Matthias

Regards,
Matthias

quoted

Are there any config.txt tweaks necessary?

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel