[PATCH 23/40] arm64: dts: renesas: Switch eMMC bus to 1V8 on Salvator-X and ULCB
From: Simon Horman <hidden>
Date: 2018-11-26 12:54:49
Also in:
linux-renesas-soc
Subsystem:
arm/risc-v/renesas architecture, the rest · Maintainers:
Geert Uytterhoeven, Magnus Damm, Linus Torvalds
From: Marek Vasut <marek.vasut@gmail.com> The eMMC card has two supplies, VCC and VCCQ. The VCC supplies the NAND array and the VCCQ supplies the bus. On Salvator-X and ULCB, the VCC is connected to 3.3V rail, while the VCCQ is connected to 1.8V rail. Adjust the pinmux to match the bus, which is always operating in 1.8V mode. While at it, deduplicate the pinmux entries, which are now the same for both default and UHS modes. We still need the two pinctrl entries to match the bindings though. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <redacted> --- arch/arm64/boot/dts/renesas/salvator-common.dtsi | 8 +------- arch/arm64/boot/dts/renesas/ulcb.dtsi | 8 +------- 2 files changed, 2 insertions(+), 14 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index a3e89504e044..f66d990b92f1 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi@@ -607,12 +607,6 @@ sdhi2_pins: sd2 { groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; function = "sdhi2"; - power-source = <3300>; - }; - - sdhi2_pins_uhs: sd2_uhs { - groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; - function = "sdhi2"; power-source = <1800>; };
@@ -763,7 +757,7 @@ &sdhi2 { /* used for on-board 8bit eMMC */ pinctrl-0 = <&sdhi2_pins>; - pinctrl-1 = <&sdhi2_pins_uhs>; + pinctrl-1 = <&sdhi2_pins>; pinctrl-names = "default", "state_uhs"; vmmc-supply = <®_3p3v>;
diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi
index 89daca7356df..de694fdae067 100644
--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi@@ -332,12 +332,6 @@ sdhi2_pins: sd2 { groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; function = "sdhi2"; - power-source = <3300>; - }; - - sdhi2_pins_uhs: sd2_uhs { - groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds"; - function = "sdhi2"; power-source = <1800>; };
@@ -426,7 +420,7 @@ &sdhi2 { /* used for on-board 8bit eMMC */ pinctrl-0 = <&sdhi2_pins>; - pinctrl-1 = <&sdhi2_pins_uhs>; + pinctrl-1 = <&sdhi2_pins>; pinctrl-names = "default", "state_uhs"; vmmc-supply = <®_3p3v>;
--
2.11.0