[PATCH V2 2/3] ARM: dts: add Raspberry Pi 3 A+
From: Stefan Wahren <hidden>
Date: 2018-11-15 23:00:03
Subsystem:
arm and arm64 soc sub-architectures (common parts), the rest · Maintainers:
Arnd Bergmann, Krzysztof Kozlowski, Alexandre Belloni, Linus Walleij, Linus Torvalds
The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM, 1 USB 2.0 port and no Ethernet. Signed-off-by: Stefan Wahren <redacted> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 107 +++++++++++++++++++++++++++++ 2 files changed, 108 insertions(+) create mode 100644 arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d..15bbd0d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile@@ -79,6 +79,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \ bcm2835-rpi-a-plus.dtb \ bcm2835-rpi-cm1-io1.dtb \ bcm2836-rpi-2-b.dtb \ + bcm2837-rpi-3-a-plus.dtb \ bcm2837-rpi-3-b.dtb \ bcm2837-rpi-3-b-plus.dtb \ bcm2837-rpi-cm3-io3.dtb \
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
new file mode 100644
index 0000000..75785dd
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts@@ -0,0 +1,107 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; +#include "bcm2837.dtsi" +#include "bcm2836-rpi.dtsi" +#include "bcm283x-rpi-usb-host.dtsi" + +/ { + compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837"; + model = "Raspberry Pi 3 Model A+"; + + chosen { + /* 8250 auxiliary UART instead of pl011 */ + stdout-path = "serial1:115200n8"; + }; + + memory { + reg = <0 0x20000000>; + }; + + leds { + act { + gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; + }; + + pwr { + label = "PWR"; + gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; + }; + }; + + wifi_pwrseq: wifi-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>; + }; +}; + +&firmware { + expgpio: gpio { + compatible = "raspberrypi,firmware-gpio"; + gpio-controller; + #gpio-cells = <2>; + gpio-line-names = "BT_ON", + "WL_ON", + "STATUS_LED", + "", + "", + "CAM_GPIO0", + "CAM_GPIO1", + ""; + status = "okay"; + }; +}; + +&hdmi { + hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>; + status = "okay"; +}; + +/* SDHCI is used to control the SDIO for wireless */ +&sdhci { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_gpio34>; + status = "okay"; + bus-width = <4>; + non-removable; + mmc-pwrseq = <&wifi_pwrseq>; + + brcmf: wifi at 1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* SDHOST is used to drive the SD card */ +&sdhost { + pinctrl-names = "default"; + pinctrl-0 = <&sdhost_gpio48>; + status = "okay"; + bus-width = <4>; +}; + +/* uart0 communicates with the BT module */ +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <2000000>; + shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; + }; +}; + +/* uart1 is mapped to the pin header */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; +};
--
2.7.4