[PATCH v3 25/25] arm64: dts: allwinner: a64-amarula-relic: Enable Techstar TS8550B MIPI-DSI panel
From: jagan@amarulasolutions.com (Jagan Teki)
Date: 2018-10-26 14:46:37
Also in:
dri-devel, linux-clk, linux-devicetree, lkml
Subsystem:
arm/allwinner sunxi soc support, the rest · Maintainers:
Chen-Yu Tsai, Jernej Skrabec, Samuel Holland, Linus Torvalds
Amarula A64-Relic board by default bound with Techstar TS8550B MIPI-DSI panel, add support for it. DSI panel connected via board DSI port with, - DC1SW as AVDD supply - DCDC2 as DVDD supply - DCDC1 as VCC-DSI supply - PD24 gpio for reset pin - PD23 gpio for backlight enable pin Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> --- Changes for v3: - new patch .../allwinner/sun50i-a64-amarula-relic.dts | 46 +++++++++++++++++++ 1 file changed, 46 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index 6cb2b7f0c817..ecc0d8094815 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts@@ -9,6 +9,7 @@ #include "sun50i-a64.dtsi" #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> / { model = "Amarula A64-Relic";
@@ -18,6 +19,14 @@ serial0 = &uart0; }; + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <1 2 4 8 16 32 64 128 512>; + default-brightness-level = <2>; + enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* LCD-BL-EN: PD23 */ + }; + chosen { stdout-path = "serial0:115200n8"; };
@@ -30,6 +39,28 @@ }; }; +&de { + status = "okay"; +}; + +&dphy { + status = "okay"; +}; + +&dsi { + vcc-dsi-supply = <®_dldo1>; + status = "okay"; + + panel at 0 { + compatible = "techstar,ts8550b"; + reg = <0>; + avdd-supply = <®_dc1sw>; + dvdd-supply = <®_dldo2>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* LCD-RST: PD24 */ + backlight = <&backlight>; + }; +}; + &ehci0 { status = "okay"; };
@@ -72,6 +103,12 @@ status = "okay"; }; +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pin>; + status = "okay"; +}; + &r_rsb { status = "okay";
@@ -107,6 +144,15 @@ regulator-name = "vcc-pll-avcc"; }; +®_dc1sw { + /* + * This regulator also indirectly drives the PD pingroup GPIOs, + * which also controls the power LED. + */ + regulator-always-on; + regulator-name = "vcc-phy"; +}; + ®_dcdc1 { regulator-always-on; regulator-min-microvolt = <3300000>;
--
2.18.0.321.gffc6fa0e3