Hi Rocky,

Am Freitag, 11. August 2017, 17:46:55 CEST schrieb rocky.hao:

Hi Caesar,
Thanks for your comments.

just to add, there is no need to resend, I can drop the comments
here myself when applying :-)


Heiko

Best Regards,
Rocky

? 2017/8/11 14:44, Caesar Wang ??:

quoted

? 2017?08?04? 16:06, Rocky Hao ??:

quoted

add thermal zone and dynamic CPU power coefficients for rk3328

Signed-off-by: Rocky Hao <redacted>
---
Change in v2:
- remove gerrit Change-Id

  arch/arm64/boot/dts/rockchip/rk3328.dtsi | 43 
++++++++++++++++++++++++++++++++
  1 file changed, 43 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi 

b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 186fb93fdffd..68829f808320 100644

--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi

@@ -47,6 +47,7 @@
  #include <dt-bindings/pinctrl/rockchip.h>
  #include <dt-bindings/power/rk3328-power.h>
  #include <dt-bindings/soc/rockchip,boot-mode.h>
+#include <dt-bindings/thermal/thermal.h>
  / {
      compatible = "rockchip,rk3328";

@@ -74,6 +75,8 @@
              compatible = "arm,cortex-a53", "arm,armv8";
              reg = <0x0 0x0>;
              clocks = <&cru ARMCLK>;
+            #cooling-cells = <2>; /* min followed by max */
+            dynamic-power-coefficient = <120>;
              enable-method = "psci";
              next-level-cache = <&l2>;
          };

@@ -83,6 +86,7 @@
              compatible = "arm,cortex-a53", "arm,armv8";
              reg = <0x0 0x1>;
              clocks = <&cru ARMCLK>;
+            dynamic-power-coefficient = <120>;
              enable-method = "psci";
              next-level-cache = <&l2>;
          };

@@ -92,6 +96,7 @@
              compatible = "arm,cortex-a53", "arm,armv8";
              reg = <0x0 0x2>;
              clocks = <&cru ARMCLK>;
+            dynamic-power-coefficient = <120>;
              enable-method = "psci";
              next-level-cache = <&l2>;
          };

@@ -101,6 +106,7 @@
              compatible = "arm,cortex-a53", "arm,armv8";
              reg = <0x0 0x3>;
              clocks = <&cru ARMCLK>;
+            dynamic-power-coefficient = <120>;
              enable-method = "psci";
              next-level-cache = <&l2>;
          };

@@ -308,6 +314,43 @@
          interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
      };
+    thermal-zones {
+        soc_thermal: soc-thermal {
+            polling-delay-passive = <20>; /* milliseconds */
+            polling-delay = <1000>; /* milliseconds */
+            sustainable-power = <1000>; /* milliwatts */
+
+            thermal-sensors = <&tsadc 0>;
+
+            trips {
+                threshold: trip-point0 {
+                    temperature = <70000>; /* millicelsius */
+                    hysteresis = <2000>; /* millicelsius */
+                    type = "passive";
+                };
+                target: trip-point1 {
+                    temperature = <85000>; /* millicelsius */
+                    hysteresis = <2000>; /* millicelsius */
+                    type = "passive";
+                };
+                soc_crit: soc-crit {
+                    temperature = <95000>; /* millicelsius */
+                    hysteresis = <2000>; /* millicelsius */

The document had already described, maybe we should remove the 
millicelsius/milliseconds/milliwatts here.

It is ok for me.

quoted

quoted

+                    type = "critical";
+                };
+            };
+
+            cooling-maps {
+                map0 {
+                    trip = <&target>;
+                    cooling-device = <&cpu0 THERMAL_NO_LIMIT 
THERMAL_NO_LIMIT>;
+                    contribution = <4096>;
+                };
+            };
+        };
+
+    };
+
      tsadc: tsadc at ff250000 {
          compatible = "rockchip,rk3328-tsadc";
          reg = <0x0 0xff250000 0x0 0x100>;