[PATCH V8 07/11] iommu: of: Handle IOMMU lookup failure with deferred probing or error

On 5/3/2017 3:24 PM, Robin Murphy wrote:

quoted

On 02/05/17 19:35, Geert Uytterhoeven wrote:

quoted

On Fri, Feb 3, 2017 at 4:48 PM, Sricharan R wrote:

quoted

From: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

Failures to look up an IOMMU when parsing the DT iommus property need to
be handled separately from the .of_xlate() failures to support deferred
probing.

The lack of a registered IOMMU can be caused by the lack of a driver for
the IOMMU, the IOMMU device probe not having been performed yet, having
been deferred, or having failed.

The first case occurs when the device tree describes the bus master and
IOMMU topology correctly but no device driver exists for the IOMMU yet
or the device driver has not been compiled in. Return NULL, the caller
will configure the device without an IOMMU.

The second and third cases are handled by deferring the probe of the bus
master device which will eventually get reprobed after the IOMMU.

The last case is currently handled by deferring the probe of the bus
master device as well. A mechanism to either configure the bus master
device without an IOMMU or to fail the bus master device probe depending
on whether the IOMMU is optional or mandatory would be a good
enhancement.

Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Laurent Pichart
[off-list ref]
Signed-off-by: Sricharan R <redacted>

This patch broke Renesas R-Car Gen3 platforms in renesas-drivers.
As the IOMMU nodes in DT are not yet enabled, all devices having iommus
properties in DT now fail to probe.

How exactly do they fail to probe? Per d7b0558230e4, if there are no ops
registered then they should merely defer until we reach the point of
giving up and ignoring the IOMMU. Is it just that you have no other
late-probing drivers or post-init module loads to kick the deferred
queue after that point? I did try to find a way to explicitly kick it
from a suitably late initcall, but there didn't seem to be any obvious
public interface - anyone have any suggestions?

I think that's more of a general problem with the probe deferral
mechanism itself (I've seen the same thing happen with some of the
CoreSight stuff on Juno due to the number of inter-component
dependencies) rather than any specific fault of this series.

I was thinking of an additional check like below to avoid the
situation ?

From 499b6e662f60f23740b8880882b0a16f16434501 Mon Sep 17 00:00:00 2001
From: Sricharan R <redacted>
Date: Wed, 3 May 2017 13:16:59 +0530
Subject: [PATCH] iommu: of: Fix check for returning EPROBE_DEFER

While returning EPROBE_DEFER for iommu masters
take in to account of iommu nodes that could be
marked in DT as 'status=disabled', in which case
simply return NULL and let the master's probe
continue rather than deferring.

Signed-off-by: Sricharan R <redacted>
---
 drivers/iommu/of_iommu.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/iommu/of_iommu.c b/drivers/iommu/of_iommu.c
index 9f44ee8..e6e9bec 100644
--- a/drivers/iommu/of_iommu.c
+++ b/drivers/iommu/of_iommu.c

@@ -118,6 +118,7 @@ static bool of_iommu_driver_present(struct device_node

*np)

        ops = iommu_ops_from_fwnode(fwnode);
        if ((ops && !ops->of_xlate) ||
+           !of_device_is_available(iommu_spec->np) ||
            (!ops && !of_iommu_driver_present(iommu_spec->np)))
                return NULL;