[PATCH v5 2/2] ARM: dts: add support for Turris Omnia

omnia:~ # ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
default qlen 532
    link/ether d8:58:d7:00:61:70 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group
default qlen 532
    link/ether d8:58:d7:00:61:6e brd ff:ff:ff:ff:ff:ff
4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP
group default qlen 532
    link/ether d8:58:d7:00:61:6f brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.50/24 brd 192.168.1.255 scope global eth2
       valid_lft forever preferred_lft forever
    inet6 2003:86:6702:9f00:da58:d7ff:fe00:616f/64 scope global
mngtmpaddr dynamic
       valid_lft 7050sec preferred_lft 1650sec
    inet6 fe80::da58:d7ff:fe00:616f/64 scope link
       valid_lft forever preferred_lft forever
5: sit0 at NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1
    link/sit 0.0.0.0 brd 0.0.0.0
6: lan0 at eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state
DOWN group default qlen 1000
    link/ether d8:58:d7:00:61:6e brd ff:ff:ff:ff:ff:ff
7: lan1 at eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state
DOWN group default qlen 1000
    link/ether d8:58:d7:00:61:6e brd ff:ff:ff:ff:ff:ff
8: lan2 at eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state
DOWN group default qlen 1000
    link/ether d8:58:d7:00:61:6e brd ff:ff:ff:ff:ff:ff
9: lan3 at eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state
DOWN group default qlen 1000
    link/ether d8:58:d7:00:61:6e brd ff:ff:ff:ff:ff:ff
10: lan4 at eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state
DOWN group default qlen 1000
    link/ether d8:58:d7:00:61:6e brd ff:ff:ff:ff:ff:ff

I get some interfaces for the switch, but I've not been able to get them
up/usable.

ip link set eth1 up

Feel free to browse my commits, maybe I'm doing something
stupid - I already tried with and without fixed links, but the driver
seems to use only one of the two cpu links.

Correct, and this has been discussed on the thread about this board.

	 Andrew