[PATCH 8/9] ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
From: Chen-Yu Tsai <hidden>
Date: 2016-08-21 03:08:07
Also in:
linux-devicetree, lkml
Subsystem:
the rest · Maintainer:
Linus Torvalds
The AXP806 PMIC is the secondary PMIC. It provides various supply voltages for the SoC and other peripherals. The PMIC's interrupt line is connected to NMI pin of the SoC. Signed-off-by: Chen-Yu Tsai <redacted> --- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 112 ++++++++++++++++++++++++++++ 1 file changed, 112 insertions(+)
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 910b29f0f0b5..e38ac4fec10c 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts@@ -260,6 +260,118 @@ }; }; + axp806: pmic at 745 { + compatible = "x-powers,axp806"; + reg = <0x745>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + bldoin-supply = <®_dcdce>; + + regulators { + reg_s_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; + }; + + aldo2 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo2"; + }; + + aldo3 { + /* + * unused, but use a different name to + * avoid name clash with axp809's aldo's + */ + regulator-name = "s_aldo3"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-name = "vcc18-efuse-adc-display-csi"; + }; + + reg_bldo2: bldo2 { + regulator-always-on; + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <1980000>; + regulator-name = + "vdd18-drampll-vcc18-pll-cpvdd"; + }; + + bldo3 { + /* unused */ + }; + + reg_bldo4: bldo4 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1320000>; + regulator-name = "vcc12-hsic"; + }; + + reg_cldo1: cldo1 { + /* + * This was 3V in the original design, but + * 3.3V is the recommended supply voltage + * for the Ethernet PHY. + */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-gmac-phy"; + }; + + reg_cldo2: cldo2 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "afvcc-cam"; + }; + + reg_cldo3: cldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-io-wifi-codec-io2"; + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpub"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-vpu"; + }; + + reg_dcdce: dcdce { + regulator-always-on; + regulator-min-microvolt = <2100000>; + regulator-max-microvolt = <2100000>; + regulator-name = "vcc-bldo-codec-ldoin"; + }; + + sw { + /* + * unused, but use a different name to + * avoid name clash with axp809's sw + */ + regulator-name = "s_sw"; + }; + }; + }; + ac100: codec at e89 { compatible = "x-powers,ac100"; reg = <0xe89>;
--
2.9.3