[PATCH 6/7] arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board
From: cw00.choi@samsung.com (Chanwoo Choi)
Date: 2016-08-19 01:04:27
Also in:
linux-devicetree, linux-samsung-soc, lkml
Hi Rob, On 2016? 08? 19? 04:08, Rob Herring wrote:
On Tue, Aug 16, 2016 at 03:35:27PM +0900, Chanwoo Choi wrote:quoted
This patch adds the Device Tree source for Exynos5433-based Samsung TM2 board. This board fully support the all things for mobile target. This patch supports the following devices: 1. basic SoC - Initial booting for Samsung Exynos5433 SoC - DRAM LPDDR3 (3GB) - eMMC (32GB) - ARM architecture timer 2. power management devices - Sasmung S2MPS13 PMIC for the power supply - CPUFREQ for big.LITTLE cores - TMU for big.LITTLE cores and GPU - ADC with thermistor to measure the temperature of AP/Battery/Charger - Maxim MAX77843 Interface PMIC (MUIC/Fuel-gauge/Charger/Haptic/LED/Regulator) 3. sound devices - I2S for sound bus - LPASS for sound power control - Wolfson WM5110 for sound codec - Maxim MAX98504 for speaker amplifier - TM2 ASoC Machine device driver node 3. display devices - DECON, DSI and MIC for the panel output 4. usb devices - USB 3.0 DRD (Dual Role Device) - USB 3.0 Host controller 5. storage devices - MSHC (obile Storae Host Controller) for eMMC device 6. misc devices - gpio-keys (power, volume up/down, home key) - PWM (Pulse Width Modulation Timer) Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Joonyoung Shim <redacted> Signed-off-by: Inki Dae <inki.dae@samsung.com> Signed-off-by: Jonghwa Lee <redacted> Signed-off-by: Beomho Seo <redacted> Signed-off-by: Jaewon Kim <redacted> Signed-off-by: Hyungwon Hwang <redacted> Signed-off-by: Inha Song <redacted> Signed-off-by: Ingi kim <redacted> Signed-off-by: Krzysztof Kozlowski <redacted> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andrzej Hajda <redacted> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> --- .../bindings/arm/samsung/samsung-boards.txt | 1 + arch/arm64/boot/dts/exynos/Makefile | 5 +- arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 1003 ++++++++++++++++++++ 3 files changed, 1008 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2.dtsdiff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt index 0ea7f14ef294..c704b4bf6137 100644 --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt@@ -15,6 +15,7 @@ Required root node properties: - "samsung,xyref5260" - for Exynos5260-based Samsung board. - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board. - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board. + - "samsung,tm2" - for Exynos5333-based Samsung TM2 board. - "samsung,sd5v1" - for Exynos5440-based Samsung board. - "samsung,ssdk5440" - for Exynos5440-based Samsung board.diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile index 50c9b9383cfa..7ddea53769a7 100644 --- a/arch/arm64/boot/dts/exynos/Makefile +++ b/arch/arm64/boot/dts/exynos/Makefile@@ -1,4 +1,7 @@ -dtb-$(CONFIG_ARCH_EXYNOS) += exynos7-espresso.dtb +dtb-$(CONFIG_ARCH_EXYNOS) += \ + exynos5433-tm2.dtb \ + exynos5433-tm2e.dtb \ + exynos7-espresso.dtb always := $(dtb-y) subdir-y := $(dts-dirs)diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts new file mode 100644 index 000000000000..3e497b0d0015 --- /dev/null +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts@@ -0,0 +1,1003 @@ +/* + * SAMSUNG Exynos5433 TM2 board device tree source + * + * Copyright (c) 2016 Samsung Electronics Co., Ltd. + * + * Device tree source file for Samsung's TM2 board which is based on + * Samsung Exynos5433 SoC. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos5433.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Samsung TM2 board"; + compatible = "samsung,exynos5433-tm2", "samsung,exynos5433"; + + aliases { + i2c0 = &hsi2c_0; + i2c1 = &hsi2c_1; + i2c2 = &hsi2c_2; + i2c3 = &hsi2c_3; + i2c4 = &hsi2c_4; + i2c5 = &hsi2c_5; + i2c6 = &hsi2c_6; + i2c7 = &hsi2c_7; + i2c8 = &hsi2c_8; + i2c9 = &hsi2c_9; + i2c10 = &hsi2c_10; + i2c11 = &hsi2c_11; + mshc0 = &mshc_0; + mshc1 = &mshc_1; + mshc2 = &mshc_2; + pinctrl0 = &pinctrl_alive; + pinctrl1 = &pinctrl_aud; + pinctrl2 = &pinctrl_cpif; + pinctrl3 = &pinctrl_ese; + pinctrl4 = &pinctrl_finger; + pinctrl5 = &pinctrl_fsys; + pinctrl6 = &pinctrl_imem; + pinctrl7 = &pinctrl_nfc; + pinctrl8 = &pinctrl_peric; + pinctrl9 = &pinctrl_touch; + serial0 = &serial_0; + serial1 = &serial_1; + serial2 = &serial_2; + serial3 = &serial_3; + spi0 = &spi_0; + spi1 = &spi_1; + spi2 = &spi_2; + spi3 = &spi_3; + spi4 = &spi_4; + usbdrdphy0 = &usbdrd30_phy;Please drop all these aliases except for serial.
I'll remain the pinctrl/spi/serial and then drop the else aliases. The alias id pinctrl/spi/serial are used.
quoted
+ }; + + chosen { + stdout-path = &serial_1; + }; + + memory at 20000000 { + device_type = "memory"; + reg = <0x0 0x20000000 0x0 0xc0000000>; + }; + + gpio_keys {Use -, not _.
OK.
quoted
+ compatible = "gpio-keys"; + + power_key {ditto...
OK.
quoted
+ gpios = <&gpa2 7 1>; + linux,code = <KEY_POWER>; + label = "power key"; + debounce-interval = <10>; + gpio-key,wakeup;This is legacy. Use the common binding.
I'll remove it.
quoted
+ }; + + volume_up_key { + gpios = <&gpa2 0 1>; + linux,code = <KEY_VOLUMEUP>; + label = "volume-up key"; + debounce-interval = <10>; + }; + + volume_down_key { + gpios = <&gpa2 1 1>; + linux,code = <KEY_VOLUMEDOWN>; + label = "volume-down key"; + debounce-interval = <10>; + }; + + homepage_key { + gpios = <&gpa0 3 1>; + linux,code = <KEY_MENU>; + label = "homepage key"; + debounce-interval = <10>; + }; + }; + + i2c_max98504: i2c-gpio-0 { + compatible = "i2c-gpio"; + gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */ + &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + max98504: max98504 at 31 { + compatible = "maxim,max98504"; + reg = <0x31>; + maxim,rx-path = <1>; + maxim,tx-path = <1>; + maxim,tx-channel-mask = <3>; + maxim,tx-channel-source = <2>; + }; + }; + + sound { + compatible = "samsung,tm2-audio"; + audio-codec = <&wm5110>; + i2s-controller = <&i2s0>; + audio-amplifier = <&max98504>; + mic-bias-gpios = <&gpr3 2 0>; + model = "wm5110"; + samsung,audio-routing = + /* Headphone */ + "HP", "HPOUT1L", + "HP", "HPOUT1R", + + /* Speaker */ + "SPK", "SPKOUT", + "SPKOUT", "HPOUT2L", + "SPKOUT", "HPOUT2R", + + /* Receiver */ + "RCV", "HPOUT3L", + "RCV", "HPOUT3R"; + status = "okay"; + }; +}; + +&adc { + vdd-supply = <&ldo3_reg>; + status = "okay"; + + thermistor-ap { + compatible = "ntc,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <0>; + io-channels = <&adc 0>; + }; + + thermistor_battery: thermistor-battery { + compatible = "ntc,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <0>; + io-channels = <&adc 1>; + #thermal-sensor-cells = <0>; + }; + + thermistor-charger { + compatible = "ntc,ncp03wf104"; + pullup-uv = <1800000>; + pullup-ohm = <100000>; + pulldown-ohm = <0>; + io-channels = <&adc 2>; + }; +}; + +&cpu0 { + cpu-supply = <&buck3_reg>; +}; + +&cpu4 { + cpu-supply = <&buck2_reg>; +}; + +&decon { + status = "okay"; + iommu-reserved-mapping = <0x20000000 0x20000000 0xc0000000>; + + i80-if-timings { + }; +}; + +&dsi { + status = "okay"; + vddcore-supply = <&ldo6_reg>; + vddio-supply = <&ldo7_reg>; + samsung,pll-clock-frequency = <24000000>; + pinctrl-names = "default"; + pinctrl-0 = <&te_irq>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 1 { + reg = <1>; + + dsi_out: endpoint { + samsung,burst-clock-frequency = <512000000>; + samsung,esc-clock-frequency = <16000000>; + }; + }; + }; +}; + +&hsi2c_0 { + status = "okay"; + clock-frequency = <2500000>; + + s2mps13_pmic at 66 {Use '-'
OK.
quoted
+ compatible = "samsung,s2mps13-pmic"; + interrupt-parent = <&gpa0>; + interrupts = <7 0>; + reg = <0x66>; + wakeup;Use the common binding.
I'll remove it.
quoted
+ samsung,s2mps11-wrstbi-ground; + + s2mps13_osc: clocks { + compatible = "samsung,s2mps13-clk"; + #clock-cells = <1>; + clock-output-names = "s2mps13_ap", "s2mps13_cp", + "s2mps13_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "VDD_ALIVE_0.9V_AP"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "VDDQ_MMC2_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo3_reg: LDO3 { + regulator-name = "VDD1_E_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "VDD10_MIF_PLL_1.0V_AP"; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo5_reg: LDO5 { + regulator-name = "VDD10_DPLL_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo6_reg: LDO6 { + regulator-name = "VDD10_MIPI2L_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo7_reg: LDO7 { + regulator-name = "VDD18_MIPI2L_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "VDD18_LLI_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo9_reg: LDO9 { + regulator-name = "VDD18_ABB_ETC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo10_reg: LDO10 { + regulator-name = "VDD33_USB30_3.0V_AP"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo11_reg: LDO11 { + regulator-name = "VDD_INT_M_1.0V_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo12_reg: LDO12 { + regulator-name = "VDD_KFC_M_1.1V_AP"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + ldo13_reg: LDO13 { + regulator-name = "VDD_G3D_M_0.95V_AP"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <950000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo14_reg: LDO14 { + regulator-name = "VDDQ_M1_LDO_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo15_reg: LDO15 { + regulator-name = "VDDQ_M2_LDO_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + ldo16_reg: LDO16 { + regulator-name = "VDDQ_EFUSE"; + regulator-min-microvolt = <1400000>; + regulator-max-microvolt = <3400000>; + regulator-always-on; + }; + + ldo17_reg: LDO17 { + regulator-name = "V_TFLASH_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo18_reg: LDO18 { + regulator-name = "V_CODEC_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo19_reg: LDO19 { + regulator-name = "VDDA_1.8V_COMP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo20_reg: LDO20 { + regulator-name = "VCC_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + ldo21_reg: LDO21 { + regulator-name = "VT_CAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo22_reg: LDO22 { + regulator-name = "CAM_IO_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo23_reg: LDO23 { + regulator-name = "CAM_SEN_CORE_1.2V_AP"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1200000>; + }; + + ldo24_reg: LDO24 { + regulator-name = "VT_CAM_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + ldo25_reg: LDO25 { + regulator-name = "CAM_SEN_A2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo26_reg: LDO26 { + regulator-name = "CAM_AF_2.8V_AP"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo27_reg: LDO27 { + regulator-name = "VCC_3.0V_LCD_AP"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo28_reg: LDO28 { + regulator-name = "VCC_1.8V_LCD_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo29_reg: LDO29 { + regulator-name = "VT_CAM_2.8V"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo30_reg: LDO30 { + regulator-name = "TSP_AVDD_3.3V_AP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo31_reg: LDO31 { + regulator-name = "TSP_VDD_1.85V_AP"; + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + }; + + ldo32_reg: LDO32 { + regulator-name = "VTOUCH_1.8V_AP"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + ldo33_reg: LDO33 { + regulator-name = "VTOUCH_LED_3.3V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-ramp-delay = <12500>; + }; + + ldo34_reg: LDO34 { + regulator-name = "VCC_1.8V_MHL_AP"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2100000>; + }; + + ldo35_reg: LDO35 { + regulator-name = "OIS_VM_2.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo36_reg: LDO36 { + regulator-name = "VSIL_1.0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo37_reg: LDO37 { + regulator-name = "VF_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo38_reg: LDO38 { + regulator-name = "VCC_3.0V_MOTOR_AP"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo39_reg: LDO39 { + regulator-name = "V_HRM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo40_reg: LDO40 { + regulator-name = "V_HRM_3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_MIF_0.9V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck2_reg: BUCK2 { + regulator-name = "VDD_EGL_1.0V_AP"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck3_reg: BUCK3 { + regulator-name = "VDD_KFC_1.0V_AP"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck4_reg: BUCK4 { + regulator-name = "VDD_INT_0.95V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck5_reg: BUCK5 { + regulator-name = "VDD_DISP_CAM0_0.9V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck6_reg: BUCK6 { + regulator-name = "VDD_G3D_0.9V_AP"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-state-mem { + regulator-off-in-suspend; + }; + }; + + buck7_reg: BUCK7 { + regulator-name = "VDD_MEM1_1.2V_AP"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "VDD_LLDO_1.35V_AP"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + buck9_reg: BUCK9 { + regulator-name = "VDD_MLDO_2.0V_AP"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + buck10_reg: BUCK10 { + regulator-name = "vdd_mem2"; + regulator-min-microvolt = <550000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + }; + }; + }; +}; + +&hsi2c_8 { + status = "okay"; + + max77843 at 66 { + compatible = "samsung,max77843"; + interrupt-parent = <&gpa1>; + interrupts = <5 2>; + reg = <0x66>; + wakeup;Use common binding.
I'll remove it.
quoted
+ + muic: max77843-muic { + compatible = "maxim,max77843-muic"; + };
Regards, Chanwoo Choi