On Mon, Mar 21, 2016 at 10:02 PM, Giuseppe CAVALLARO
[off-list ref] wrote:

On 3/21/2016 11:45 AM, Alexandre Torgue wrote:

quoted

Hi,

2016-03-18 17:00 GMT+01:00 Chen-Yu Tsai [off-list ref]:

quoted

Hi,

On Fri, Mar 18, 2016 at 11:37 PM, Alexandre TORGUE
[off-list ref] wrote:

quoted

Signed-off-by: Alexandre TORGUE <redacted>

diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt

b/Documentation/devicetree/bindings/net/stm32-dwmac.txt
new file mode 100644
index 0000000..ada2aa4

--- /dev/null
+++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt

@@ -0,0 +1,32 @@
+STMicroelectronics STM32 / MCU DWMAC glue layer controller
+
+This file documents platform glue layer for stmmac.
+Please see stmmac.txt for the other unchanged properties.
+
+The device node has following properties.
+
+Required properties:
+- compatible:  Should be "st,stm32-dwmac" to select glue, and
+              "snps,dwmac-3.50a" to select IP vesrion.

Almost all the synp gmac chips have the HW capability register that is
used for setting all the parameters at probe time.
This will override fields passed from DT. In theory, it is not
necessary to pass: "snps,dwmac-3.50a" from device tree at least there
is either no HW cap reg or the glue has some w/a for a specific chip
revision.
To be honest, I like to see the "snps,dwmac-3.50a" as compatibility
to also have a better readability (that's my personal view ;-) ).

I agree having the versioned strings is good for informational purposes,
and to signal hardware capability. It is not so good for directly
binding drivers in the implementation though.

Unfortunately, as Joachim pointed out, exynos5440 uses it so we cannot
change it.

ChenYu

Peppe

quoted

quoted

If you need have sort of hardware glue, then it is not compatible.

We could have the case where the glue is set by a bootloader.
In this case, we will select IP version in compatible and we will use
generic dwmac glue to probe stmmac driver.

Regards

Alex.

quoted

ChenYu

quoted

+- clocks: Must contain a phandle for each entry in clock-names.
+- clock-names: Should be "stmmaceth" for the host clock.
+              Should be "tx-clk" for the MAC TX clock.
+              Should be "rx-clk" for the MAC RX clock.
+- st,syscon : Should be phandle/offset pair. The phandle to the syscon
node which
+             encompases the glue register, and the offset of the
control register.
+Example:
+
+               ethernet0: dwmac at 40028000 {
+                       compatible = "st,stm32-dwmac",
"snps,dwmac-3.50a";
+                       status = "disabled";
+                       reg = <0x40028000 0x8000>;
+                       reg-names = "stmmaceth";
+                       interrupts = <0 61 0>, <0 62 0>;
+                       interrupt-names = "macirq", "eth_wake_irq";
+                       clock-names = "stmmaceth", "tx-clk", "rx-clk";
+                       clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>;
+                       st,syscon = <&syscfg 0x4>;
+                       snps,pbl = <8>;
+                       snps,mixed-burst;
+                       dma-ranges;
+               };
--
1.9.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel