[PATCH v4 3/3] touchscreen: colibri-vf50-ts: Add touchscreen support for Colibri VF50

Hi Sanchayan,

On Fri, Aug 21, 2015 at 06:56:32PM +0530, Sanchayan Maity wrote:

The Colibri Vybrid VF50 module supports 4-wire touchscreens using
FETs and ADC inputs. This driver uses the IIO consumer interface
and relies on the vf610_adc driver based on the IIO framework.

Thank you for making changes. I have a few comments still.

Can we possibly add "|| COMPILE_TEST" dependency? Will it compile
without IIO or VF610_ADC enabled?

Don't you need gpio/consumer.h?

+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define DRIVER_NAME "colibri-vf50-ts"
+#define DRV_VERSION "1.0"
+
+#define VF_ADC_MAX ((1 << 12) - 1)
+
+#define COLI_TOUCH_MIN_DELAY_US 1000
+#define COLI_TOUCH_MAX_DELAY_US 2000
+#define COLI_TOUCH_NO_OF_AVGS	5
+
+struct vf50_touch_device {
+	struct platform_device	*pdev;
+	struct input_dev	*ts_input;
+	struct iio_channel	*channels;
+	struct gpio_desc *gpio_xp;
+	struct gpio_desc *gpio_xm;
+	struct gpio_desc *gpio_yp;
+	struct gpio_desc *gpio_ym;
+	struct gpio_desc *gpio_pen_detect;

I do not see gpio_pen_detect being used anymore.

+	int pen_irq;
+	int min_pressure;
+	bool stop_touchscreen;
+};
+
+/*
+ * Enables given plates and measures touch parameters using ADC
+ */
+static int adc_ts_measure(struct iio_channel *channel,
+		  struct gpio_desc *plate_p, struct gpio_desc *plate_m)
+{
+	int i, value = 0, val = 0;
+	int ret;
+
+	gpiod_set_value(plate_p, 1);
+	gpiod_set_value(plate_m, 1);
+
+	usleep_range(COLI_TOUCH_MIN_DELAY_US, COLI_TOUCH_MAX_DELAY_US);
+
+	for (i = 0; i < COLI_TOUCH_NO_OF_AVGS; i++) {
+		ret = iio_read_channel_raw(channel, &val);
+		if (ret < 0) {
+			value = ret;
+			goto error_iio_read;
+		}
+
+		value += val;
+	}
+
+	value /= COLI_TOUCH_NO_OF_AVGS;
+
+error_iio_read:
+	gpiod_set_value(plate_p, 0);
+	gpiod_set_value(plate_m, 0);
+
+	return value;
+}
+
+/*
+ * Enable touch detection using falling edge detection on XM
+ */
+static void vf50_ts_enable_touch_detection(struct vf50_touch_device *vf50_ts)
+{
+	/* Enable plate YM (needs to be strong GND, high active) */
+	gpiod_set_value(vf50_ts->gpio_ym, 1);
+
+	/*
+	 * Let the platform mux to idle state in order to enable
+	 * Pull-Up on GPIO
+	 */
+	pinctrl_pm_select_idle_state(&vf50_ts->pdev->dev);
+}
+
+/*
+ * ADC touch screen sampling bottom half irq handler
+ */
+static irqreturn_t vf50_ts_irq_bh(int irq, void *private)
+{
+	struct vf50_touch_device *vf50_ts = (struct vf50_touch_device *)private;

No need to cast from void * pointer.

+	struct device *dev = &vf50_ts->pdev->dev;
+	int val_x, val_y, val_z1, val_z2, val_p = 0;
+	bool discard_val_on_start = true;
+
+	/* Disable the touch detection plates */
+	gpiod_set_value(vf50_ts->gpio_ym, 0);
+
+	/* Let the platform mux to default state in order to mux as ADC */
+	pinctrl_pm_select_default_state(dev);
+
+	while (!vf50_ts->stop_touchscreen) {
+		/* X-Direction */
+		val_x = adc_ts_measure(&vf50_ts->channels[0],
+				vf50_ts->gpio_xp, vf50_ts->gpio_xm);
+		if (val_x < 0)
+			break;
+
+		/* Y-Direction */
+		val_y = adc_ts_measure(&vf50_ts->channels[1],
+				vf50_ts->gpio_yp, vf50_ts->gpio_ym);
+		if (val_y < 0)
+			break;
+
+		/*
+		 * Touch pressure
+		 * Measure on XP/YM
+		 */
+		val_z1 = adc_ts_measure(&vf50_ts->channels[2],
+				vf50_ts->gpio_yp, vf50_ts->gpio_xm);
+		if (val_z1 < 0)
+			break;
+		val_z2 = adc_ts_measure(&vf50_ts->channels[3],
+				vf50_ts->gpio_yp, vf50_ts->gpio_xm);
+		if (val_z2 < 0)
+			break;
+
+		/* Validate signal (avoid calculation using noise) */
+		if (val_z1 > 64 && val_x > 64) {
+			/*
+			 * Calculate resistance between the plates
+			 * lower resistance means higher pressure
+			 */
+			int r_x = (1000 * val_x) / VF_ADC_MAX;
+
+			val_p = (r_x * val_z2) / val_z1 - r_x;
+
+		} else {
+			val_p = 2000;
+		}
+
+		val_p = 2000 - val_p;
+		dev_dbg(dev, "Measured values: x: %d, y: %d, z1: %d, z2: %d, "
+			"p: %d\n", val_x, val_y, val_z1, val_z2, val_p);
+
+		/*
+		 * If touch pressure is too low, stop measuring and reenable
+		 * touch detection
+		 */
+		if (val_p < vf50_ts->min_pressure || val_p > 2000)
+			break;
+
+		/*
+		 * The pressure may not be enough for the first x and the
+		 * second y measurement, but, the pressure is ok when the
+		 * driver is doing the third and fourth measurement. To
+		 * take care of this, we drop the first measurement always.
+		 */
+		if (discard_val_on_start) {
+			discard_val_on_start = false;
+		} else {
+			/*
+			 * Report touch position and sleep for
+			 * next measurement
+			 */
+			input_report_abs(vf50_ts->ts_input,
+					ABS_X, VF_ADC_MAX - val_x);
+			input_report_abs(vf50_ts->ts_input,
+					ABS_Y, VF_ADC_MAX - val_y);
+			input_report_abs(vf50_ts->ts_input,
+					ABS_PRESSURE, val_p);
+			input_report_key(vf50_ts->ts_input, BTN_TOUCH, 1);
+			input_sync(vf50_ts->ts_input);
+		}
+
+		msleep(10);
+	}
+
+	/* Report no more touch, reenable touch detection */
+	input_report_abs(vf50_ts->ts_input, ABS_PRESSURE, 0);
+	input_report_key(vf50_ts->ts_input, BTN_TOUCH, 0);
+	input_sync(vf50_ts->ts_input);
+
+	vf50_ts_enable_touch_detection(vf50_ts);
+
+	/* Wait for the pull-up to be stable on high */
+	msleep(10);
+
+	return IRQ_HANDLED;
+}
+
+static int vf50_ts_open(struct input_dev *dev_input)
+{
+	struct vf50_touch_device *touchdev = input_get_drvdata(dev_input);
+	struct device *dev = &touchdev->pdev->dev;
+
+	dev_dbg(dev, "Input device %s opened, starting touch detection\n",
+			dev_input->name);
+
+	touchdev->stop_touchscreen = false;
+
+	/* Mux detection before request IRQ, wait for pull-up to settle */
+	vf50_ts_enable_touch_detection(touchdev);
+	msleep(10);
+
+	return 0;
+}
+
+static void vf50_ts_close(struct input_dev *dev_input)
+{
+	struct vf50_touch_device *touchdev = input_get_drvdata(dev_input);
+	struct device *dev = &touchdev->pdev->dev;
+
+	touchdev->stop_touchscreen = true;
+
+	/* Make sure IRQ is not running past close */
+	mb();
+	synchronize_irq(touchdev->pen_irq);
+

Should we drive the gpio_ym inactive here? What about pin control?

+	dev_dbg(dev, "Input device %s closed, disable touch detection\n",
+		dev_input->name);
+}
+
+static int vf50_ts_get_gpiod(struct device *dev,
+	struct gpio_desc **gpio_d, const char *con_id, enum gpiod_flags flags)
+{
+	int error;
+
+	*gpio_d = devm_gpiod_get(dev, con_id, flags);
+	if (IS_ERR(*gpio_d)) {
+		error = PTR_ERR(*gpio_d);
+		dev_err(dev, "Could not get gpio_%s %d\n", con_id, error);
+		return error;
+	}
+
+	return 0;
+}
+
+static void vf50_ts_channel_release(void *data)
+{
+	struct vf50_touch_device *touchdev = data;
+
+	iio_channel_release_all(touchdev->channels);
+}
+
+static int vf50_ts_probe(struct platform_device *pdev)
+{
+	struct input_dev *input;
+	struct iio_channel *channels;
+	struct device *dev = &pdev->dev;
+	struct vf50_touch_device *touchdev;
+	int error;
+
+	channels = iio_channel_get_all(dev);
+	if (IS_ERR(channels))
+		return PTR_ERR(channels);
+
+	touchdev = devm_kzalloc(dev, sizeof(*touchdev), GFP_KERNEL);
+	if (!touchdev) {
+		error = -ENOMEM;
+		return error;

Why not simply

		return -ENOMEM;

here?

Also you are leaking your iio channels here. You need to install the
custom action earlier.

+	}
+
+	error = of_property_read_u32(dev->of_node, "vf50-ts-min-pressure",
+				 &touchdev->min_pressure);
+	if (error)
+		return error;
+
+	error = devm_add_action(dev, vf50_ts_channel_release, channels);
+	if (error) {
+		dev_err(dev, "Failed to register iio channel release action");

You also need

		vf50_ts_channel_release(touchdev);

+		return error;
+	}
+
+	input = devm_input_allocate_device(dev);
+	if (!input) {
+		dev_err(dev, "Failed to allocate TS input device\n");
+		error = -ENOMEM;
+		return error;

Again simply return error code, no need to assign to the error variable.

+	}
+
+	platform_set_drvdata(pdev, touchdev);
+
+	touchdev->pdev = pdev;
+	touchdev->channels = channels;
+
+	input->name = DRIVER_NAME;
+	input->id.bustype = BUS_HOST;
+	input->dev.parent = dev;
+	input->open = vf50_ts_open;
+	input->close = vf50_ts_close;
+
+	input_set_capability(input, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(input, ABS_X, 0, VF_ADC_MAX, 0, 0);
+	input_set_abs_params(input, ABS_Y, 0, VF_ADC_MAX, 0, 0);
+	input_set_abs_params(input, ABS_PRESSURE, 0, VF_ADC_MAX, 0, 0);
+
+	touchdev->ts_input = input;
+	input_set_drvdata(input, touchdev);
+	error = input_register_device(input);
+	if (error) {
+		dev_err(dev, "Failed to register input device\n");
+		return error;
+	}
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_xp,
+				"xp", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_xm,
+				"xm", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_yp,
+				"yp", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	error = vf50_ts_get_gpiod(dev, &touchdev->gpio_ym,
+				"ym", GPIOD_OUT_LOW);
+	if (error)
+		return error;
+
+	touchdev->pen_irq = platform_get_irq(pdev, 0);
+	if (touchdev->pen_irq < 0)
+		return touchdev->pen_irq;
+
+	error = devm_request_threaded_irq(dev, touchdev->pen_irq, NULL,
+			vf50_ts_irq_bh, IRQF_ONESHOT,
+			"vf50 touch", touchdev);
+	if (error < 0)
+		return error;
+
+	return 0;
+}
+
+static const struct of_device_id vf50_touch_of_match[] = {
+	{ .compatible = "toradex,vf50-touchscreen", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, vf50_touch_of_match);
+
+static struct platform_driver vf50_touch_driver = {
+	.driver = {
+		.name = "toradex,vf50_touchctrl",
+		.of_match_table = vf50_touch_of_match,
+	},
+	.probe = vf50_ts_probe,
+};
+
+module_platform_driver(vf50_touch_driver);
+
+MODULE_AUTHOR("Sanchayan Maity");
+MODULE_DESCRIPTION("Colibri VF50 Touchscreen driver");
+MODULE_LICENSE("GPL v2");

Please change it to "GPL" which means GPL v2+ to match license notice at
the top.

+MODULE_VERSION(DRV_VERSION);
-- 
2.5.0

Thank you.

-- 
Dmitry