Thread (32 messages) 32 messages, 3 authors, 2015-07-20

[PATCH v5 07/12] mtd: nand: add Samsung K9GBG08U0A-M to nand_ids table

From: ezequiel@vanguardiasur.com.ar (Ezequiel Garcia)
Date: 2015-05-24 18:45:30
Also in: lkml
Subsystem: memory technology devices (mtd), nand flash subsystem, the rest · Maintainers: Miquel Raynal, Richard Weinberger, Vignesh Raghavendra, Linus Torvalds

Antoine,

On 05/20/2015 11:43 AM, Antoine Tenart wrote:
[..]
quoted
I just had a look on the datasheet, and I you're right, the nand should
support JDEC. However I get a "No NAND device found" error when
reverting this patch.

It seems nand_flash_detect_jedec() is not reading "JDEC" and is returning
directly. I'm having a look at this.
So, I can read 'J', 'E', 'D' and 'E' but then I got 0xff's. So I tried
to only check of JEDE in nand_flash_detect_jedec() but the JEDEC
parameter page was then not valid.
This uncovers two different bugs in the driver.

1. read_id_bytes is either '2' or '4', but JEDEC detections needs at
least 5 bytes.

2. The initial buffer (to read the ID and the parameter page) has
256 bytes, but the JEDEC parameter page is 512-bytes.

And while at it, the driver doesn't seem to support reading the
redundant parameter pages (recently reported on barebox ML [1]). So this
is a third bug.

Would you try setting read_id_bytes to '5' and also increasing the READ_PARAM
transfer length? Something like this:
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 1259cc5..851372f 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -48,7 +48,7 @@
  * STATUS, READID and PARAM. The largest of these is the PARAM command,
  * needing 256 bytes.
  */
-#define INIT_BUFFER_SIZE	256
+#define INIT_BUFFER_SIZE	2048
 
 /* registers and bit definitions */
 #define NDCR		(0x00) /* Control register */
@@ -899,18 +899,18 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 		break;
 
 	case NAND_CMD_PARAM:
-		info->buf_count = 256;
+		info->buf_count = 2048;
 		info->ndcb0 |= NDCB0_CMD_TYPE(0)
 				| NDCB0_ADDR_CYC(1)
 				| NDCB0_LEN_OVRD
 				| command;
 		info->ndcb1 = (column & 0xFF);
-		info->ndcb3 = 256;
-		info->data_size = 256;
+		info->ndcb3 = 2048;
+		info->data_size = 2048;
 		break;
[1] http://lists.infradead.org/pipermail/barebox/2015-May/023515.html

Thanks,
-- 
Ezequiel Garcia, VanguardiaSur
www.vanguardiasur.com.ar
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help