[PATCH v5 05/12] mtd: pxa3xx_nand: rework flash detection and timing setup
From: ezequiel@vanguardiasur.com.ar (Ezequiel Garcia)
Date: 2015-05-16 22:06:00
Also in:
lkml
Antoine, On 05/11/2015 11:58 AM, Antoine Tenart wrote:
quoted hunk ↗ jump to hunk
Rework the pxa3xx_nand driver to allow using functions exported by the nand framework to detect the flash and the timings. Then setup the timings using the helpers previously added. Signed-off-by: Antoine Tenart <redacted> --- drivers/mtd/nand/pxa3xx_nand.c | 114 ++++++++++------------------------------- 1 file changed, 26 insertions(+), 88 deletions(-)diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c index b5aad4c46115..6d8d191ee05b 100644 --- a/drivers/mtd/nand/pxa3xx_nand.c +++ b/drivers/mtd/nand/pxa3xx_nand.c@@ -1322,48 +1322,25 @@ static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) return NAND_STATUS_READY; } -static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info, - const struct pxa3xx_nand_flash *f) +static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info) { struct platform_device *pdev = info->pdev; struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); struct pxa3xx_nand_host *host = info->host[info->cs]; + struct mtd_info *mtd = host->mtd; + struct nand_chip *chip = mtd->priv; uint32_t ndcr = 0x0; /* enable all interrupts */ - if (f->page_size != 2048 && f->page_size != 512) { - dev_err(&pdev->dev, "Current only support 2048 and 512 size\n"); - return -EINVAL; - } - - if (f->flash_width != 16 && f->flash_width != 8) { - dev_err(&pdev->dev, "Only support 8bit and 16 bit!\n"); - return -EINVAL; - } - - /* calculate flash information */ - host->read_id_bytes = (f->page_size == 2048) ? 4 : 2; - - /* calculate addressing information */ - host->col_addr_cycles = (f->page_size == 2048) ? 2 : 1; - - if (f->num_blocks * f->page_per_block > 65536) - host->row_addr_cycles = 3; - else - host->row_addr_cycles = 2; - ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0; ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0; - ndcr |= (f->page_per_block == 64) ? NDCR_PG_PER_BLK : 0; - ndcr |= (f->page_size == 2048) ? NDCR_PAGE_SZ : 0; - ndcr |= (f->flash_width == 16) ? NDCR_DWIDTH_M : 0; - ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0; + ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0; + ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0;
By the time you call this, there's no detected flash, so there's no geometry information such as mtd->writesize, chip->page_shift, etc.
quoted hunk ↗ jump to hunk
ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes); ndcr |= NDCR_SPARE_EN; /* enable spare by default */ info->reg_ndcr = ndcr; - pxa3xx_nand_set_timing(host, f->timing); return 0; }@@ -1458,20 +1435,28 @@ static void pxa3xx_nand_free_buff(struct pxa3xx_nand_info *info) } #endif -static int pxa3xx_nand_sensing(struct pxa3xx_nand_info *info) +static int pxa3xx_nand_sensing(struct pxa3xx_nand_host *host) { + struct pxa3xx_nand_info *info = host->info_data; struct mtd_info *mtd; struct nand_chip *chip; + const struct nand_sdr_timings *timings; int ret; mtd = info->host[info->cs]->mtd; chip = mtd->priv; - /* use the common timing to make a try */ - ret = pxa3xx_nand_config_flash(info, &builtin_flash_types[0]); + ret = pxa3xx_nand_config_flash(info); if (ret) return ret; + /* use the common timing to make a try */ + timings = onfi_async_timing_mode_to_sdr_timings(0); + if (IS_ERR(timings)) + return PTR_ERR(timings); + + pxa3xx_nand_set_sdr_timing(host, timings); + chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0); ret = chip->waitfunc(mtd, chip); if (ret & NAND_STATUS_FAIL)@@ -1555,12 +1540,8 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd) struct pxa3xx_nand_info *info = host->info_data; struct platform_device *pdev = info->pdev; struct pxa3xx_nand_platform_data *pdata = dev_get_platdata(&pdev->dev); - struct nand_flash_dev pxa3xx_flash_ids[2], *def = NULL; - const struct pxa3xx_nand_flash *f = NULL; struct nand_chip *chip = mtd->priv; - uint32_t id = -1; - uint64_t chipsize; - int i, ret, num; + int ret; uint16_t ecc_strength, ecc_step; if (pdata->keep_config && !pxa3xx_nand_detect_config(info))@@ -1569,7 +1550,7 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd) /* Set a default chunk size */ info->chunk_size = 512; - ret = pxa3xx_nand_sensing(info); + ret = pxa3xx_nand_sensing(host); if (ret) { dev_info(&info->pdev->dev, "There is no chip on cs %d!\n", info->cs);@@ -1577,64 +1558,20 @@ static int pxa3xx_nand_scan(struct mtd_info *mtd) return ret; } - chip->cmdfunc(mtd, NAND_CMD_READID, 0, 0); - id = *((uint16_t *)(info->data_buff)); - if (id != 0) - dev_info(&info->pdev->dev, "Detect a flash id %x\n", id); - else { - dev_warn(&info->pdev->dev, - "Read out ID 0, potential timing set wrong!!\n"); - - return -EINVAL; - } - - num = ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1; - for (i = 0; i < num; i++) { - if (i < pdata->num_flash) - f = pdata->flash + i; - else - f = &builtin_flash_types[i - pdata->num_flash + 1]; - - /* find the chip in default list */ - if (f->chip_id == id) - break; - } - - if (i >= (ARRAY_SIZE(builtin_flash_types) + pdata->num_flash - 1)) { - dev_err(&info->pdev->dev, "ERROR!! flash not defined!!!\n"); - - return -EINVAL; - } - - ret = pxa3xx_nand_config_flash(info, f);
This second call to pxa3xx_nand_config_flash was in charge of re-configuring the device after proper identification. I'd say a proper approach is to configure default parameters, call nand_scan_ident, and finally re-configure using the detected values. READ_ID should only needs a few parameters to work (e.g. read_id_bytes), and those are the ones that need an initial default. The rest can remain null until the device is known. Regarding read_id_bytes default value, using '4' makes sense and should work in all cases.
- if (ret) {
- dev_err(&info->pdev->dev, "ERROR! Configure failed\n");
- return ret;
- }
-
- memset(pxa3xx_flash_ids, 0, sizeof(pxa3xx_flash_ids));
-
- pxa3xx_flash_ids[0].name = f->name;
- pxa3xx_flash_ids[0].dev_id = (f->chip_id >> 8) & 0xffff;
- pxa3xx_flash_ids[0].pagesize = f->page_size;
- chipsize = (uint64_t)f->num_blocks * f->page_per_block * f->page_size;
- pxa3xx_flash_ids[0].chipsize = chipsize >> 20;
- pxa3xx_flash_ids[0].erasesize = f->page_size * f->page_per_block;
- if (f->flash_width == 16)
- pxa3xx_flash_ids[0].options = NAND_BUSWIDTH_16;
- pxa3xx_flash_ids[1].name = NULL;
- def = pxa3xx_flash_ids;
KEEP_CONFIG:
- if (info->reg_ndcr & NDCR_DWIDTH_M)
- chip->options |= NAND_BUSWIDTH_16;
-
/* Device detection must be done with ECC disabled */
if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370)
nand_writel(info, NDECCCTRL, 0x0);
- if (nand_scan_ident(mtd, 1, def))
+ if (nand_scan_ident(mtd, 1, NULL))
return -ENODEV;
We only want to configure timings if keep_config is false. Otherwise, this breaks on platforms that don't have timings and don't support ONFI.
quoted hunk ↗ jump to hunk
+ ret = pxa3xx_nand_init_timings(host); + if (ret) { + dev_err(&info->pdev->dev, "Failed to set timings: %d\n", ret); + return ret; + } + if (pdata->flash_bbt) { /* * We'll use a bad block table stored in-flash and don't@@ -1732,6 +1669,7 @@ static int alloc_nand_resource(struct platform_device *pdev) host->mtd = mtd; host->cs = cs; host->info_data = info; + host->read_id_bytes = 4; mtd->priv = host; mtd->owner = THIS_MODULE;
Aside from this comments, I really like this four patches. They clean most of the mess and introduce proper timing configuration. In fact, this cleanup might help removing the keep_config property on mvebu boards. Thanks for the work, -- Ezequiel Garcia, VanguardiaSur www.vanguardiasur.com.ar