Am Freitag, den 06.03.2015, 11:40 -0800 schrieb Stephen Boyd:

On 03/06/15 11:28, Uwe Kleine-K?nig wrote:

quoted

Hello Mike,

On Fri, Mar 06, 2015 at 10:57:30AM -0800, Mike Turquette wrote:

quoted

Quoting Uwe Kleine-K?nig (2015-02-21 02:40:22)

quoted

Hello,

TLDR: only apply patch 1 and rip of CLK_DIVIDER_ROUND_CLOSEST.

I stared at clk-divider.c for some time now given Sascha's failing test
case. I found a fix for the failure (which happens to be what Sascha
suspected).

The other two patches fix problems only present when handling dividers
that have CLK_DIVIDER_ROUND_CLOSEST set. Note that these are still
heavily broken however. So having a 4bit-divider and a parent clk of
10000 (as in Sascha's test case) requesting

        clk_set_rate(clk, 666)

sets the rate to 625 (div=15) instead of 667 (div=16). The reason is the
choice of parent_rate in clk_divider_bestdiv's loop is wrong for
CLK_DIVIDER_ROUND_CLOSEST (with and without patch 1). A fix here is
non-trivial and for sure more than one rate must be tested here. This is
complicated by the fact that clk_round_rate might return a value bigger
than the requested rate which convinces me (once more) that it's a bad
idea to allow that. Even if this was fixed for .round_rate,
clk_divider_set_rate is still broken because it also uses

        div = DIV_ROUND_UP(parent_rate, rate);

to calculate the (pretended) best divider to get near rate.

Note this makes at least two reasons to remove support for
CLK_DIVIDER_ROUND_CLOSEST!

Instead I'd favour creating a function

        clk_round_rate_nearest

as was suggested some time ago by Soren Brinkmann and me[1] that doesn't

Uwe,

Thanks for the fixes. I'm thinking of taking all three for 4.0. I also
agree on clk_round_rate_nearest (along with a _ceil and _floor version
as well). That's something we can do for 4.1 probably.

I'd say that we make round_rate the _floor version. I guess in most
cases that already does the right thing. Also I think 4.1 is very
ambitious, so my suggestion for 4.1 is:

 - add a WARN_ON_ONCE to clk_round_rate catching calls that return a
   value bigger than requested.
 - implement clk_round_rate_nearest using clk_round_rate and the
   assumption that it returns a value that is <= the requested rate.
   I think without that there are too many special cases to handle and
   probably not even a reliable way to determine the nearest rate.
 - while we're at it tightening the requirements for clk_round_rate
   let's also specify the expected rounding. I'd vote for the
   mathematical rounding, that is

   	clk_round_rate(someclk, 333)

   explicitly is allowed to return a rate bigger than 333 as long as it
   is less than 333.5.

At one point while developing patch 1 I had the dividers fixed for the
rounding issue. I think I still have that patch somewhere so can post it
as RFC.

Why do we need clk_round_rate_nearest? We have rate constraints now so
drivers should be moving towards requesting a rate that's within a
tolerance they can accept if they even care to enforce anything like
that. Eventually clk_round_rate() returning a value smaller or larger
than what it's called with won't matter as long as what the
implementation does fits within the constraints that consumers specify.
It may even be possible to remove clk_round_rate() as a consumer API.

If I have to provide a panel pixel clock I usually want to get a rate as
close as possible to the specified typical rate, but within the
specified limits.

Assume a panel with 70 MHz ideal pixel clock and a valid range of 60 MHz
to 80 MHz. If the clock supply supports two frequencies within that
range, 60 MHz and 72 MHz, I'd prefer 72 MHz to be chosen over 60 Mhz.

regards
Philipp