[PATCH 6/9] ARM: Kirkwood: Convert GoFlex Net to pinctrl.
From: Josh Coombs <hidden>
Date: 2012-10-28 14:31:27
Tested-by: Joshua Coombs <redacted> On Wed, Oct 24, 2012 at 10:53 AM, Andrew Lunn [off-list ref] wrote:
quoted hunk ↗ jump to hunk
Signed-off-by: Andrew Lunn <andrew@lunn.ch> --- arch/arm/boot/dts/kirkwood-goflexnet.dts | 57 ++++++++++++++++++++++++++++++ arch/arm/mach-kirkwood/board-goflexnet.c | 18 ---------- 2 files changed, 57 insertions(+), 18 deletions(-)diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts index 7c8238f..46d16a2 100644 --- a/arch/arm/boot/dts/kirkwood-goflexnet.dts +++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts@@ -16,6 +16,63 @@ }; ocp at f1000000 { + pinctrl: pinctrl at 10000 { + compatible = "marvell,88f6281-pinctrl"; + reg = <0x10000 0x20>; + + pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange + &pmx_led_left_cap_0 &pmx_led_left_cap_1 + &pmx_led_left_cap_2 &pmx_led_left_cap_3 + &pmx_led_right_cap_0 &pmx_led_right_cap_1 + &pmx_led_right_cap_2 &pmx_led_right_cap_3 + >; + pinctrl-names = "default"; + + pmx_usb_power_enable: pmx-usb-power-enable { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + pmx_led_right_cap_0: pmx-led_right_cap_0 { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; + pmx_led_right_cap_1: pmx-led_right_cap_1 { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + pmx_led_right_cap_2: pmx-led_right_cap_2 { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + pmx_led_right_cap_3: pmx-led_right_cap_3 { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + pmx_led_left_cap_0: pmx-led_left_cap_0 { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + pmx_led_left_cap_1: pmx-led_left_cap_1 { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + pmx_led_left_cap_2: pmx-led_left_cap_2 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + pmx_led_left_cap_3: pmx-led_left_cap_3 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + pmx_led_green: pmx-led_green { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + pmx_led_orange: pmx-led_orange { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + }; serial at 12000 { clock-frequency = <200000000>; status = "ok";diff --git a/arch/arm/mach-kirkwood/board-goflexnet.c b/arch/arm/mach-kirkwood/board-goflexnet.c index 001ca8c..9643f4b 100644 --- a/arch/arm/mach-kirkwood/board-goflexnet.c +++ b/arch/arm/mach-kirkwood/board-goflexnet.c@@ -34,34 +34,16 @@ #include <mach/bridge-regs.h> #include <linux/platform_data/mmc-mvsdio.h> #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data goflexnet_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(0), }; -static unsigned int goflexnet_mpp_config[] __initdata = { - MPP29_GPIO, /* USB Power Enable */ - MPP47_GPIO, /* LED Orange */ - MPP46_GPIO, /* LED Green */ - MPP45_GPIO, /* LED Left Capacity 3 */ - MPP44_GPIO, /* LED Left Capacity 2 */ - MPP43_GPIO, /* LED Left Capacity 1 */ - MPP42_GPIO, /* LED Left Capacity 0 */ - MPP41_GPIO, /* LED Right Capacity 3 */ - MPP40_GPIO, /* LED Right Capacity 2 */ - MPP39_GPIO, /* LED Right Capacity 1 */ - MPP38_GPIO, /* LED Right Capacity 0 */ - 0 -}; - void __init goflexnet_init(void) { /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(goflexnet_mpp_config); - if (gpio_request(29, "USB Power Enable") != 0 || gpio_direction_output(29, 1) != 0) pr_err("can't setup GPIO 29 (USB Power Enable)\n"); --1.7.10.4