[PATCH 1/5] dmaengine: mxs-dma: add dma support for i.MX23/28

Hi,

On Sat, Feb 05, 2011 at 10:08:12AM +0800, Shawn Guo wrote:

quoted

This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.

* apbh-dma and apbx-dma are supported in the driver as two instances,
  and have to be filtered by dma clients via device id.  It becomes
  the convention that apbh-dma always gets registered prior to
  apbx-dma.

* apbh-dma is different between mx23 and mx28, hardware version
  register is used to handle the differences.

* Every the mxs dma channel is statically assigned to client device
  by soc design with fixed irq.  The irq number is being passed by
  alloc_chan function with mxs_dma_data, and client driver has to
  filter the correct channel by its channel id.

* mxs-dma supports pio function besides data transfer.  The driver
  uses dma_data_direction DMA_NONE to identify the pio mode, and
  steals sgl and sg_len to get pio words and numbers from clients.

* mxs dmaengine has some very specific features, like sense function
  and the special NAND support (nand_lock, nand_wait4ready).  These
  are too specific to implemented in generic dmaengine driver.

* The parameter "flags" of prep functions is currently being used to
  pass wait4end flag from clients.

* The driver refers to imx-sdma and only a single descriptor is
  statically assigned to each channel.

Signed-off-by: Shawn Guo <redacted>
---
 arch/arm/mach-mxs/include/mach/dma.h |   16 +
 drivers/dma/Kconfig                  |    8 +
 drivers/dma/Makefile                 |    1 +
 drivers/dma/mxs-dma.c                |  702 ++++++++++++++++++++++++++++++++++
 4 files changed, 727 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-mxs/include/mach/dma.h
 create mode 100644 drivers/dma/mxs-dma.c

diff --git a/arch/arm/mach-mxs/include/mach/dma.h b/arch/arm/mach-mxs/include/mach/dma.h
new file mode 100644
index 0000000..429f431
--- /dev/null
+++ b/arch/arm/mach-mxs/include/mach/dma.h
+
+static struct dma_async_tx_descriptor *mxs_dma_prep_slave_sg(
+		struct dma_chan *chan, struct scatterlist *sgl,
+		unsigned int sg_len, enum dma_data_direction direction,
+		unsigned long flags)
+{
+	struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+	struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+	struct mxs_dma_ccw *ccw;
+	struct scatterlist *sg;
+	int ret, i, j;
+	u32 *pio;
+
+	dev_dbg(mxs_dma->dev, "%s: channel %d\n", __func__, chan->chan_id);
+
+	if (mxs_chan->status == DMA_IN_PROGRESS)
+		return NULL;
+
+	mxs_chan->status = DMA_IN_PROGRESS;
+	mxs_chan->flags = 0;
+
+	dev_dbg(mxs_dma->dev, "%s: setting up %d entries\n", __func__, sg_len);
+
+	if (sg_len > ((direction == DMA_NONE) ? MXS_PIO_WORDS : NUM_CCW)) {
+		dev_err(mxs_dma->dev, "maximum number of sg exceeded: %d > %d\n",
+				sg_len, NUM_CCW);
+		ret = -EINVAL;
+		goto err_out;
+	}
+
+	if (direction == DMA_NONE) {
+		ccw = &mxs_chan->ccw[0];
+		pio = (u32 *) sgl;
+
+		for (j = 0; j < sg_len;)
+			ccw->pio_words[j++] = *pio++;
+
+		ccw->next = 0;
+		ccw->bits.chain = 0;
+		ccw->bits.irq = 1;
+		ccw->bits.dec_sem = 1;
+		ccw->bits.wait4end = flags;
+		ccw->bits.halt_on_terminate = 1;
+		ccw->bits.terminate_flush = 1;
+		ccw->bits.pio_num = sg_len;
+		ccw->bits.command = MXS_DMA_NO_XFER;

Does this have a valid usecase? I would just return some error code
here. pio_num and pio_words are unused in the driver and I don't think
a dmaengine driver should have some kind of PIO fallback.

Actually 'PIO' is a misnomer here. It's the free scaled way of
implementing a simple feature (chained DMA with mixed transfer modes)
in a complicated and obfuscated way.

What's behinde the 'PIO' transfers is programming controller registers
via DMA along with the actual DMA data transfer. DMA_NONE simply
means, that the DMA transfer does only the register programming but
does not transfer any payload. The 'pio_words' are the values that are
being written to consecutive locations of e.g. the SPI controller
register address space.
The programming is actually done by DMA, in any case.


Lothar Wa?mann
-- 
___________________________________________________________

Ka-Ro electronics GmbH | Pascalstra?e 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Gesch?ftsf?hrer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996

www.karo-electronics.de | info at karo-electronics.de
___________________________________________________________