[PATCH 5.10 125/130] serial: 8250_pci: rewrite pericom_do_set_divisor()
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Date: 2021-12-06 15:46:29
Also in:
lkml
From: Jay Dolan <redacted>
commit bb1201d4b38ec67bd9a871cf86b0cc10f28b15b5 upstream.
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips")
Cc: stable <redacted>
Signed-off-by: Jay Dolan <redacted>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com (local)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/tty/serial/8250/8250_pci.c | 30 +++++++++++++++++-------------
1 file changed, 17 insertions(+), 13 deletions(-)
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c@@ -1349,29 +1349,33 @@ pericom_do_set_divisor(struct uart_port { int scr; int lcr; - int actual_baud; - int tolerance; - for (scr = 5 ; scr <= 15 ; scr++) { - actual_baud = 921600 * 16 / scr; - tolerance = actual_baud / 50; + for (scr = 16; scr > 4; scr--) { + unsigned int maxrate = port->uartclk / scr; + unsigned int divisor = max(maxrate / baud, 1U); + int delta = maxrate / divisor - baud; - if ((baud < actual_baud + tolerance) && - (baud > actual_baud - tolerance)) { + if (baud > maxrate + baud / 50) + continue; + if (delta > baud / 50) + divisor++; + + if (divisor > 0xffff) + continue; + + /* Update delta due to possible divisor change */ + delta = maxrate / divisor - baud; + if (abs(delta) < baud / 50) { lcr = serial_port_in(port, UART_LCR); serial_port_out(port, UART_LCR, lcr | 0x80); - - serial_port_out(port, UART_DLL, 1); - serial_port_out(port, UART_DLM, 0); + serial_port_out(port, UART_DLL, divisor & 0xff); + serial_port_out(port, UART_DLM, divisor >> 8 & 0xff); serial_port_out(port, 2, 16 - scr); serial_port_out(port, UART_LCR, lcr); return; - } else if (baud > actual_baud) { - break; } } - serial8250_do_set_divisor(port, baud, quot, quot_frac); } static int pci_pericom_setup(struct serial_private *priv, const struct pciserial_board *board,