[PATCH 5.10 027/221] net: enetc: set MAC RX FIFO to recommended value
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Date: 2021-03-29 08:29:36
Also in:
lkml
Subsystem:
freescale enetc ethernet drivers, networking drivers, the rest · Maintainers:
Claudiu Manoil, Vladimir Oltean, Wei Fang, Clark Wang, Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
From: Alex Marginean <redacted> [ Upstream commit 1b2395dfff5bb40228a187f21f577cd90673d344 ] On LS1028A, the MAC RX FIFO defaults to the value 2, which is too high and may lead to RX lock-up under traffic at a rate higher than 6 Gbps. Set it to 1 instead, as recommended by the hardware design team and by later versions of the ENETC block guide. Signed-off-by: Alex Marginean <redacted> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Jason Liu <redacted> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org> --- drivers/net/ethernet/freescale/enetc/enetc_hw.h | 2 ++ drivers/net/ethernet/freescale/enetc/enetc_pf.c | 6 ++++++ 2 files changed, 8 insertions(+)
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_hw.h b/drivers/net/ethernet/freescale/enetc/enetc_hw.h
index 21a6ce415cb2..2b90a345507b 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_hw.h
+++ b/drivers/net/ethernet/freescale/enetc/enetc_hw.h@@ -234,6 +234,8 @@ enum enetc_bdr_type {TX, RX}; #define ENETC_PM0_MAXFRM 0x8014 #define ENETC_SET_TX_MTU(val) ((val) << 16) #define ENETC_SET_MAXFRM(val) ((val) & 0xffff) +#define ENETC_PM0_RX_FIFO 0x801c +#define ENETC_PM0_RX_FIFO_VAL 1 #define ENETC_PM_IMDIO_BASE 0x8030
diff --git a/drivers/net/ethernet/freescale/enetc/enetc_pf.c b/drivers/net/ethernet/freescale/enetc/enetc_pf.c
index 83187cd59fdd..68133563a40c 100644
--- a/drivers/net/ethernet/freescale/enetc/enetc_pf.c
+++ b/drivers/net/ethernet/freescale/enetc/enetc_pf.c@@ -490,6 +490,12 @@ static void enetc_configure_port_mac(struct enetc_hw *hw) enetc_port_wr(hw, ENETC_PM1_CMD_CFG, ENETC_PM0_CMD_PHY_TX_EN | ENETC_PM0_CMD_TXP | ENETC_PM0_PROMISC); + + /* On LS1028A, the MAC RX FIFO defaults to 2, which is too high + * and may lead to RX lock-up under traffic. Set it to 1 instead, + * as recommended by the hardware team. + */ + enetc_port_wr(hw, ENETC_PM0_RX_FIFO, ENETC_PM0_RX_FIFO_VAL); } static void enetc_mac_config(struct enetc_hw *hw, phy_interface_t phy_mode)
--
2.30.1