[PATCH net-next v3 6/9] net: dsa: realtek: rtl8365mb: use raw VID for PVID on family D

@@ -44,6 +44,10 @@
  *
  * VLANMC index 0 is reserved as a neutral PVID, used for standalone ports.
  *
+ * Everything above describes chips that have a VLAN membership configuration
+ * table. RTL8365MB_FAMILY_D chips do not have one: their PVID is a raw 12-bit
+ * VID in a per-port register, and no VLANMC entries are allocated.
+ *
  */
 
 #include "rtl8365mb_vlan.h"

@@ -119,6 +123,11 @@
 #define   RTL8365MB_VLAN_PVID_CTRL_PORT_MCIDX_MASK(_p) \
 		(0x1F << RTL8365MB_VLAN_PVID_CTRL_PORT_MCIDX_OFFSET(_p))
 
+#define RTL8365MB_D_VLAN_PVID_CTRL_BASE			0x0700
+#define RTL8365MB_D_VLAN_PVID_CTRL_REG(port) \
+	(RTL8365MB_D_VLAN_PVID_CTRL_BASE + (port))
+#define RTL8365MB_D_VLAN_PVID_CTRL_MASK			GENMASK(11, 0)
+
 /* Frame type filtering registers */
 #define RTL8365MB_VLAN_ACCEPT_FRAME_TYPE_BASE	0x07aa
 #define RTL8365MB_VLAN_ACCEPT_FRAME_TYPE_REG(port) \

@@ -170,7 +179,7 @@ struct rtl8365mb_vlan4k {
  * This structure is used to get/set entries in the VLAN membership
  * configuration database. This feature is largely vestigial, but
  * still needed for at least the following features:
- *   - PVID configuration
+ *   - PVID configuration (family C only, family D has no VLAN MC table)
  *   - ACL configuration
  *   - selection of VLAN by the CPU tag when VSEL=1, although the switch
  *     can also select VLAN based on the VLAN tag if VSEL=0

@@ -742,11 +751,25 @@ int rtl8365mb_vlan_port_get_pvid(struct realtek_priv *priv, int port, u16 *pvid)
 	u8 vlanmc_idx;
 	int ret;
 
-	ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &vlanmc_idx, &vlanmc);
-	if (ret)
-		return ret;
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D) {
+		u32 data;
+
+		ret = regmap_read(priv->map,
+				  RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				  &data);
+		if (ret)
+			return ret;
+
+		*pvid = data & RTL8365MB_D_VLAN_PVID_CTRL_MASK;
+	} else {
+		ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &vlanmc_idx,
+						 &vlanmc);
+		if (ret)
+			return ret;
+
+		*pvid = vlanmc.evid;
+	}
 
-	*pvid = vlanmc.evid;
 	return 0;
 }
 

@@ -811,6 +834,68 @@ rtl8365mb_vlan_port_set_framefilter(struct realtek_priv *priv,
 				  val);
 }
 
+/*
+ * rtl8365mb_vlan_pvid_port_set_direct() - Configure a port's PVID as a raw
+ * VID written to its dedicated register, for chip families without a
+ * working VLAN MC table (RTL8365MB_FAMILY_D)
+ *
+ * Reads back the previous PVID and frame filter first so both can be
+ * restored if enabling the new PVID fails partway through, matching
+ * the rollback behavior of the family-C implementation below.
+ *
+ * Context: Can sleep. Must be called with &priv->vlan_lock held.
+ * Return: 0 on success, or a negative error code on failure.
+ */
+static int rtl8365mb_vlan_pvid_port_set_direct(struct realtek_priv *priv,
+					       int port, u16 vid)
+{
+	enum rtl8365mb_frame_ingress prev_accepted_frame;
+	u32 prev_pvid;
+	int ret;
+
+	ret = regmap_read(priv->map, RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+			  &prev_pvid);
+	if (ret) {
+		dev_err(priv->dev, "Failed to read current PVID\n");
+		return ret;
+	}
+	prev_pvid &= RTL8365MB_D_VLAN_PVID_CTRL_MASK;
+
+	ret = rtl8365mb_vlan_port_get_framefilter(priv, port,
+						  &prev_accepted_frame);
+	if (ret) {
+		dev_err(priv->dev, "Failed to get current framefilter\n");
+		return ret;
+	}
+
+	ret = regmap_update_bits(priv->map,
+				 RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				 RTL8365MB_D_VLAN_PVID_CTRL_MASK,
+				 vid & RTL8365MB_D_VLAN_PVID_CTRL_MASK);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set port PVID\n");
+		return ret;
+	}
+
+	/* Changing accept frame is what enables PVID (if not enabled before) */
+	ret = rtl8365mb_vlan_port_set_framefilter(priv, port,
+						  RTL8365MB_FRAME_TYPE_ANY_FRAME);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set port frame filter\n");
+		goto undo_pvid_write;
+	}
+
+	return 0;
+
+undo_pvid_write:
+	(void)regmap_update_bits(priv->map,
+				 RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				 RTL8365MB_D_VLAN_PVID_CTRL_MASK, prev_pvid);
+	(void)rtl8365mb_vlan_port_set_framefilter(priv, port,
+						  prev_accepted_frame);
+	return ret;
+}
+
 /*
  * rtl8365mb_vlan_pvid_port_set() - Configure a port's PVID and associated
  * VLANMC entry

@@ -823,6 +908,9 @@ rtl8365mb_vlan_port_set_framefilter(struct realtek_priv *priv,
  * PVID. Gracefully unwinds and restores previous configuration if a hardware
  * write operation fails during execution.
  *
+ * On RTL8365MB_FAMILY_D there is no VLANMC table: the VID is written directly
+ * to the port's PVID register and no VLANMC entry is allocated.
+ *
  * Context: Can sleep. Must be called with &priv->vlan_lock held.
  * Takes and releases &priv->map_lock.
  * Return: 0 on success, or a negative error code on failure.

@@ -840,6 +928,13 @@ int rtl8365mb_vlan_pvid_port_set(struct dsa_switch *ds, int port, u16 vid,
 
 	lockdep_assert_held(&priv->vlan_lock);
 
+	/* This chip family has no VLAN MC table - PVID is a raw VID in a
+	 * dedicated per-port register, and there is no separate membership
+	 * table entry to allocate/track.
+	 */
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		return rtl8365mb_vlan_pvid_port_set_direct(priv, port, vid);
+
 	/* Read the old PVID exclusively to undo in case of error */
 	ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &prev_vlanmc_idx,
 					 &prev_vlanmc);

@@ -919,6 +1014,76 @@ undo_vlan_mc_port_set:
 	return ret;
 }
 
+/*
+ * rtl8365mb_vlan_pvid_port_clear_direct() - Remove a port's raw-VID PVID
+ * configuration, for chip families without a working VLAN MC table
+ * (RTL8365MB_FAMILY_D)
+ *
+ * Reads back the previous frame filter first so it can be restored if
+ * clearing the PVID register fails.
+ *
+ * Context: Can sleep. Must be called with &priv->vlan_lock held.
+ * Return: 0 on success, or a negative error code on failure.
+ */
+static int rtl8365mb_vlan_pvid_port_clear_direct(struct dsa_switch *ds,
+						 int port, u16 vid)
+{
+	enum rtl8365mb_frame_ingress prev_accepted_frame;
+	struct realtek_priv *priv = ds->priv;
+	bool filtering;
+	u32 cur_pvid;
+	int ret;
+
+	ret = regmap_read(priv->map, RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+			  &cur_pvid);
+	if (ret) {
+		dev_err(priv->dev, "Failed to read current PVID\n");
+		return ret;
+	}
+
+	/* Port is not using this VID as PVID. Nothing to remove. */
+	if ((cur_pvid & RTL8365MB_D_VLAN_PVID_CTRL_MASK) != vid)
+		return 0;
+
+	filtering = dsa_port_is_vlan_filtering(dsa_to_port(ds, port));
+
+	/* Changing accept frame is what really removes PVID. But only do
+	 * that if VLAN filtering is enabled.
+	 */
+	if (filtering) {
+		ret = rtl8365mb_vlan_port_get_framefilter(priv, port,
+							  &prev_accepted_frame);
+		if (ret) {
+			dev_err(priv->dev,
+				"Failed to get current framefilter\n");
+			return ret;
+		}
+
+		ret = rtl8365mb_vlan_port_set_framefilter(
+			priv, port, RTL8365MB_FRAME_TYPE_TAGGED_ONLY);
+		if (ret) {
+			dev_err(priv->dev, "Failed to set port frame filter\n");
+			return ret;
+		}
+	}
+
+	ret = regmap_update_bits(priv->map,
+				 RTL8365MB_D_VLAN_PVID_CTRL_REG(port),
+				 RTL8365MB_D_VLAN_PVID_CTRL_MASK, 0);
+	if (ret) {
+		dev_err(priv->dev, "Failed to set port PVID to 0\n");
+		goto undo_set_framefilter;
+	}
+
+	return 0;
+
+undo_set_framefilter:
+	if (filtering)
+		(void)rtl8365mb_vlan_port_set_framefilter(priv, port,
+							  prev_accepted_frame);
+	return ret;
+}
+
 /*
  * rtl8365mb_vlan_pvid_port_clear() - Remove a port's PVID configuration
  * @ds: dsa switch instance

@@ -928,6 +1093,9 @@ undo_vlan_mc_port_set:
  * Resets the target port's hardware PVID allocation to 0. Cleans up and frees
  * the associated VLANMC entry if no other ports are referencing it.
  *
+ * On RTL8365MB_FAMILY_D the port's PVID register is reset to 0 directly; there
+ * is no VLANMC entry to free.
+ *
  * Context: Can sleep. Must be called with &priv->vlan_lock held.
  * Takes and releases &priv->map_lock.
  * Return: 0 on success, or a negative error code on failure.

@@ -942,6 +1110,9 @@ int rtl8365mb_vlan_pvid_port_clear(struct dsa_switch *ds, int port, u16 vid)
 
 	lockdep_assert_held(&priv->vlan_lock);
 
+	if (rtl8365mb_get_family(priv) == RTL8365MB_FAMILY_D)
+		return rtl8365mb_vlan_pvid_port_clear_direct(ds, port, vid);
+
 	ret = rtl8365mb_vlan_get_pvid_mc(priv, port, &vlanmc_idx,
 					 &vlanmc);
 	if (ret) {