[PATCH net-next v2 0/6] net: ftgmac100: Add AST2700 support

Add the pieces needed for the FTGMAC100 driver to run on Aspeed AST2700
systems.

AST2700 keeps using the FTGMAC100 MAC IP, but the enablement is not
limited to a new compatible string. The SoC can boot with the MAC on
ARM64, needs the Aspeed-specific RMII mode bit programmed when a port is
wired for RMII, and requires the driver to use the upper DMA address
fields in the ring base registers and packet descriptors. Those fields
expose a 35-bit DMA address range on AST2700, so the driver must request
a mask that matches the address bits the hardware can encode.

The series first documents and wires up the aspeed,ast2700-mac
compatible. It then treats AST2700 as an Aspeed MAC in the driver,
enables the RMII mode programming, writes the AST2700 high descriptor-ring
base registers, carries the RX/TX descriptor high address bits, rebuilds
full DMA addresses before unmapping buffers, and requests a 35-bit DMA
mask. The high ring base registers are only touched for AST2700 so older
Aspeed device tree register windows remain unchanged. With that in place,
the FTGMAC100 Kconfig entry can be made available on ARM64 while keeping
the existing Aspeed MDIO dependency for AST2600 and newer ARCH_ASPEED
systems.

RGMII delay is configured at the bootloader stage, the same way it is
handled for AST2600, not by this driver. Aspeed's SDK bootloader
configures both AST2600 and AST2700 boards with the RGMII delay
disabled and advertises "phy-mode = rgmii-id" to match, mirroring the
OpenBMC bootloader change that stopped inserting delays on AST2600 so
its device trees could use the correct "rgmii-id" setting. On AST2700,
every on-chip MAC is likewise configured by the bootloader with RGMII
delay disabled and "rgmii-id" phy-mode. Because the delay is already
resolved before Linux boots, the ftgmac100 driver does not need to
program any RGMII delay for either AST2600 or AST2700.

This series has been validated on AST2700 EVB and AST2600 EVB.

Patch layout:
- patch 1 updates the binding for the AST2700 compatible, RMII RCLK gate,
  and reset support.
- patch 2 adds the AST2700 match data and OF compatible.
- patch 3 programs the AST2700 RMII enable bit.
- patch 4 makes "phy-mode" a required device tree property for AST2700
  and fails probe if it is missing.
- patch 5 adds AST2700 upper DMA address handling for rings and
  descriptors.
- patch 6 enables the Faraday/FTGMAC100 Kconfig options on ARM64 and
  selects MDIO_ASPEED for ARCH_ASPEED.

Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
---
Changes in v2:
- Make "phy-mode" a required device tree property for AST2700 and fail
  probe if it is missing, instead of silently defaulting to RGMII.
- Document in the cover letter how RGMII delay is configured at the
  bootloader stage for AST2600 and AST2700.
- Simplify the MDIO_ASPEED Kconfig select to ARCH_ASPEED only, dropping
  the redundant MACH_ASPEED_G6 condition, and update its help text to
  mention AST2700.
- Pick up Reviewed-by from Krzysztof Kozlowski on the dt-bindings patch.
- Link to v1: https://lore.kernel.org/r/20260927-support_ast2700-v1-0-9f03f29d2c82@aspeedtech.com (local)

---
Jacky Chou (6):
      dt-bindings: net: ftgmac100: Add AST2700 compatible
      net: ftgmac100: Add AST2700 compatible support
      net: ftgmac100: Enable AST2700 RMII support
      net: ftgmac100: Require phy-mode for AST2700
      net: ftgmac100: Add AST2700 upper DMA address support
      net: ftgmac100: Allow building on ARM64

 .../devicetree/bindings/net/faraday,ftgmac100.yaml |  4 +-
 drivers/net/ethernet/faraday/Kconfig               |  7 +-
 drivers/net/ethernet/faraday/ftgmac100.c           | 93 +++++++++++++++++++---
 drivers/net/ethernet/faraday/ftgmac100.h           |  7 ++
 drivers/net/mdio/Kconfig                           | 16 ++--
 5 files changed, 104 insertions(+), 23 deletions(-)
---
base-commit: a5e7d8e446af9803e37a3b6a4d416fb41178348f
change-id: 20260623-support_ast2700-68fb164da45c

Best regards,
-- 
Jacky Chou [off-list ref]