[PATCH net v2] net: phy: qca808x: handle the active-high LED polarity mode

Commit a274465cc3be ("net: phy: support 'active-high' property for PHY
LEDs") added PHY_LED_ACTIVE_HIGH but did not cover qca808x, so
qca808x_led_polarity_set() returns -EINVAL for it. phy_probe() propagates
that, leaving the mdio device unbound and phy_attach_direct() falling back
to the genphy driver.

Accepting the mode alone is not enough: led_polarity_mode records
active_low, so an explicit 'active-high' node stores 0, while
qca808x_config_init() re-asserts QCA808X_LED_ACTIVE_HIGH only for -1. The
bit does not survive the reset phy_init_hw() runs first, so the LED would
come up active-low.

An 'active-low' node needs nothing here: the bit is clear after the reset,
which is the polarity it asks for.

Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20260908105959.70453-1-donggeunyoo.kernel%40gmail.com
Cc: stable@vger.kernel.org
Fixes: a274465cc3be ("net: phy: support 'active-high' property for PHY LEDs")
Signed-off-by: Donggeun Yoo <redacted>
Assisted-by: Claude:claude-fable-5 sparse
---
v2:
  - No code change.  Rebased onto net/main.
  - Cc Rosen Penev and Christian Marangi, per Andrew Lunn -- they may have
    QCA808x hardware.  Christian wrote f203c8c77c76 ("net: phy: qcom:
    qca808x: default to LED active High if not set"), the default this
    patch extends.  If either of you can put an 'active-high' LED node on
    a QCA8081 and confirm the LED comes up the right way round, I would
    appreciate it.
  - Say why an 'active-low' node needs nothing in qca808x_config_init().
v1: https://lore.kernel.org/netdev/20260912012819.2072067-1-donggeunyoo.kernel@gmail.com/ (local)
  - Supersedes [PATCH net v3 3/3],
    20260908105959.70453-4-donggeunyoo.kernel@gmail.com, whose
    Reviewed-by from Andrew Lunn is dropped: that version only accepted
    the mode, this one also makes it survive the reset.

Compile-tested only (W=1, sparse).  I have no QCA808x hardware, and there is
no KUnit suite or MDIO mock under drivers/net/phy to exercise the MMD7 write
without it.

 drivers/net/phy/qcom/qca808x.c | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/drivers/net/phy/qcom/qca808x.c b/drivers/net/phy/qcom/qca808x.c
index 8eb51b1a006c..68fd4d0fe31b 100644
--- a/drivers/net/phy/qcom/qca808x.c
+++ b/drivers/net/phy/qcom/qca808x.c

@@ -200,8 +200,8 @@ static int qca808x_config_init(struct phy_device *phydev)
 	struct qca808x_priv *priv = phydev->priv;
 	int ret;
 
-	/* Default to LED Active High if active-low not in DT */
-	if (priv->led_polarity_mode == -1) {
+	/* Set LED Active High unless active-low was requested in DT */
+	if (priv->led_polarity_mode != 1) {
 		ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN,
 				       QCA808X_MMD7_LED_POLARITY_CTRL,
 				       QCA808X_LED_ACTIVE_HIGH);

@@ -603,6 +603,9 @@ static int qca808x_led_polarity_set(struct phy_device *phydev, int index,
 		case PHY_LED_ACTIVE_LOW:
 			active_low = true;
 			break;
+		case PHY_LED_ACTIVE_HIGH:
+			active_low = false;
+			break;
 		default:
 			return -EINVAL;
 		}

base-commit: e6b6078ea1731b05b3b552497b3bce4bf8b014ae
-- 
2.53.0