Thread (15 messages) flat view 15 messages, 2 authors, 10d ago
COOLING10d

Revision v2 of 4 in this series.

Revisions (4)
  1. v1 [diff vs current]
  2. v2 current
  3. v3 [diff vs current]
  4. v4 [diff vs current]

[PATCH net v2 5/6] net: stmmac: size the RX buffers from the frame length, not the MTU

From: Maxime Chevallier <maxime.chevallier@bootlin.com>
Date: 2026-09-10 15:14:57
Also in: linux-arm-kernel, lkml
Subsystem: networking drivers, stmmac ethernet driver, the rest · Maintainers: Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Maxime Chevallier, Linus Torvalds

When picking the buffsize to use based on the MTU, we shouldn't check
only the MTU value, but also :
 - ETH_HLEN for the L2 header,
 - up to 2 VLAN tags,
 - the FCS,
 - the NET_IP_ALIGN

The default bufsize is 1536 bytes, which is enough to contain all the
above so this hasn't surfaced before, but the addition of NET_IP_ALIGN
to the start of buffer address tripped the Jumbo selftest, leading to
this discovery.

With that, we don't need the '>=' checks on the buffer len, we can use
more consistent comparison operators in stmmac_set_bfsize.

Fixes: 286a83721720 ("stmmac: add CHAINED descriptor mode support (V4)")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
---
 .../net/ethernet/stmicro/stmmac/stmmac_main.c | 20 ++++++++++---------
 1 file changed, 11 insertions(+), 9 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 5fe7e95fdd34..3664a298574a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1536,17 +1536,17 @@ static unsigned int stmmac_rx_offset(struct stmmac_priv *priv)
 	return NET_SKB_PAD + NET_IP_ALIGN;
 }
 
-static int stmmac_set_bfsize(int mtu)
+static int stmmac_set_bfsize(int len)
 {
 	int ret;
 
-	if (mtu >= BUF_SIZE_8KiB)
+	if (len > BUF_SIZE_8KiB)
 		ret = BUF_SIZE_16KiB;
-	else if (mtu >= BUF_SIZE_4KiB)
+	else if (len > BUF_SIZE_4KiB)
 		ret = BUF_SIZE_8KiB;
-	else if (mtu >= BUF_SIZE_2KiB)
+	else if (len > BUF_SIZE_2KiB)
 		ret = BUF_SIZE_4KiB;
-	else if (mtu > DEFAULT_BUFSIZE)
+	else if (len > DEFAULT_BUFSIZE)
 		ret = BUF_SIZE_2KiB;
 	else
 		ret = DEFAULT_BUFSIZE;
@@ -4063,7 +4063,7 @@ static struct stmmac_dma_conf *
 stmmac_setup_dma_desc(struct stmmac_priv *priv, unsigned int mtu)
 {
 	struct stmmac_dma_conf *dma_conf;
-	int bfsize, ret;
+	int bfsize, len, ret;
 	u8 chan;
 
 	dma_conf = kzalloc_obj(*dma_conf);
@@ -4073,13 +4073,15 @@ stmmac_setup_dma_desc(struct stmmac_priv *priv, unsigned int mtu)
 		return ERR_PTR(-ENOMEM);
 	}
 
-	/* Returns 0 or BUF_SIZE_16KiB if mtu > 8KiB and dwmac4 or ring mode */
-	bfsize = stmmac_set_16kib_bfsize(priv, mtu);
+	len = mtu + ETH_HLEN + 2 * VLAN_HLEN + ETH_FCS_LEN + NET_IP_ALIGN;
+
+	/* Returns 0 or BUF_SIZE_16KiB if len > 8KiB and dwmac4 or ring mode */
+	bfsize = stmmac_set_16kib_bfsize(priv, len);
 	if (bfsize < 0)
 		bfsize = 0;
 
 	if (bfsize < BUF_SIZE_16KiB)
-		bfsize = stmmac_set_bfsize(mtu);
+		bfsize = stmmac_set_bfsize(len);
 
 	dma_conf->dma_buf_sz = bfsize;
 	/* Chose the tx/rx size from the already defined one in the
-- 
2.55.0
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help