[PATCH net v3] net: phy: air_en8811h: restore AN8811HB LED GPIO after MCU restart

Commit 03b4702fc5e3 ("net: phy: air_en8811h: move LED GPIO
configuration to config_init") moved the EN8811H LED GPIO setup from
probe to config_init because an MD32 restart clears the output-enable
bits.

AN8811HB follows the same initialization sequence: an8811hb_probe()
enables GPIO3/4/5, and later config_init() calls restart MD32.

Move the AN8811HB GPIO setup to the end of an8811hb_config_init(),
matching the current EN8811H path.

Fixes: 5afda1d734ed ("net: phy: air_en8811h: add Airoha AN8811HB support")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Ziyou Xu <redacted>
---
Changes in v3:
- Return the GPIO register update result directly, as suggested by
  Andrew Lunn.

Changes in v2:
- Drop the EN8811H change, merged independently as commit 03b4702fc5e3
  ("net: phy: air_en8811h: move LED GPIO configuration to config_init").
- Apply the same fix to AN8811HB per Jakub's review.
- Rebase onto netdev/main.

Not tested on AN8811HB hardware.

v2: https://lore.kernel.org/netdev/20260828032922.469449-1-xuziyougm@gmail.com/ (local)
v1: https://lore.kernel.org/netdev/20260820141034.1400439-1-xuziyougm@gmail.com/ (local)

---
 drivers/net/phy/air_en8811h.c | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)

diff --git a/drivers/net/phy/air_en8811h.c b/drivers/net/phy/air_en8811h.c
index 0eeb7b9a4..38eb18f0e 100644
--- a/drivers/net/phy/air_en8811h.c
+++ b/drivers/net/phy/air_en8811h.c

@@ -1125,13 +1125,6 @@ static int an8811hb_probe(struct phy_device *phydev)
 	if (ret)
 		goto err_dev_create;
 
-	/* Configure led gpio pins as output */
-	ret = air_phy_buckpbus_reg_modify(phydev, AN8811HB_GPIO_OUTPUT,
-					  AN8811HB_GPIO_OUTPUT_345,
-					  AN8811HB_GPIO_OUTPUT_345);
-	if (ret < 0)
-		goto err_dev_create;
-
 	return 0;
 
 err_dev_create:

@@ -1265,9 +1258,15 @@ static int an8811hb_config_init(struct phy_device *phydev)
 
 	ret = air_leds_init(phydev, EN8811H_LED_COUNT, AIR_PHY_LED_DUR,
 			    AIR_LED_MODE_USER_DEFINE);
-	if (ret < 0)
+	if (ret < 0) {
 		phydev_err(phydev, "Failed to initialize leds: %d\n", ret);
+		return ret;
+	}
 
+	/* Restore LED GPIO output enables after MCU initialization. */
+	ret = air_phy_buckpbus_reg_modify(phydev, AN8811HB_GPIO_OUTPUT,
+					  AN8811HB_GPIO_OUTPUT_345,
+					  AN8811HB_GPIO_OUTPUT_345);
 	return ret;
 }
 

base-commit: 1b78070aaef63512688aebfbc82365ef9d6660f1
-- 
2.43.0