[PATCH net v3] net: dpaa: fix mode setting
From: Michael Walle <mwalle@kernel.org>
Date: 2026-07-17 13:24:13
Also in:
lkml
Subsystem:
networking drivers, the rest · Maintainers:
Andrew Lunn, "David S. Miller", Eric Dumazet, Jakub Kicinski, Paolo Abeni, Linus Torvalds
Before converting to the phylink interface, the init function would have
set a non-reserved I/F mode in the maccfg2 register. After converting to
phylink, 0 is written as mode, which is a reserved value (although it's
the hardware default). Without a valid mode, a SGMII link is never
established between the MAC and the PHY and thus .link_up() is never
called which could set the correct mode according to the actual speed.
Fix it by setting the maximum speed of the phy_interface_t in use in
.mac_config() - just like the driver did before the phylink conversion.
Fixes: 5d93cfcf7360 ("net: dpaa: Convert to phylink")
Suggested-by: Sean Anderson <sean.anderson@linux.dev>
Signed-off-by: Michael Walle <mwalle@kernel.org>
---
I didn't grab Sean's Rb tag as this is somewhat different.
Changes in v3:
- keep the mode setting also in .adjust_link().
- reword the commit message, to be (hopefully) more precise
- Link to v2: https://lore.kernel.org/r/20260710143430.2276141-1-mwalle@kernel.org/ (local)
Changes in v2:
- the setting is/was based on the maximum speed, not the current
speed. thus, move the setting into mac_config().
- Link to v1: https://lore.kernel.org/r/20260706121011.1948906-1-mwalle@kernel.org/ (local)
.../net/ethernet/freescale/fman/fman_dtsec.c | 17 ++++++++++++-----
1 file changed, 12 insertions(+), 5 deletions(-)
diff --git a/drivers/net/ethernet/freescale/fman/fman_dtsec.c b/drivers/net/ethernet/freescale/fman/fman_dtsec.c
index fe35703c509e..b8d70c0ecb6c 100644
--- a/drivers/net/ethernet/freescale/fman/fman_dtsec.c
+++ b/drivers/net/ethernet/freescale/fman/fman_dtsec.c@@ -900,22 +900,28 @@ static void dtsec_mac_config(struct phylink_config *config, unsigned int mode, { struct mac_device *mac_dev = fman_config_to_mac(config); struct dtsec_regs __iomem *regs = mac_dev->fman_mac->regs; - u32 tmp; + u32 ecntrl, maccfg2; + + maccfg2 = ioread32be(®s->maccfg2); + maccfg2 &= ~(MACCFG2_NIBBLE_MODE | MACCFG2_BYTE_MODE); switch (state->interface) { case PHY_INTERFACE_MODE_RMII: - tmp = DTSEC_ECNTRL_RMM; + ecntrl = DTSEC_ECNTRL_RMM; + maccfg2 |= MACCFG2_NIBBLE_MODE; break; case PHY_INTERFACE_MODE_RGMII: case PHY_INTERFACE_MODE_RGMII_ID: case PHY_INTERFACE_MODE_RGMII_RXID: case PHY_INTERFACE_MODE_RGMII_TXID: - tmp = DTSEC_ECNTRL_GMIIM | DTSEC_ECNTRL_RPM; + ecntrl = DTSEC_ECNTRL_GMIIM | DTSEC_ECNTRL_RPM; + maccfg2 |= MACCFG2_BYTE_MODE; break; case PHY_INTERFACE_MODE_SGMII: case PHY_INTERFACE_MODE_1000BASEX: case PHY_INTERFACE_MODE_2500BASEX: - tmp = DTSEC_ECNTRL_TBIM | DTSEC_ECNTRL_SGMIIM; + ecntrl = DTSEC_ECNTRL_TBIM | DTSEC_ECNTRL_SGMIIM; + maccfg2 |= MACCFG2_BYTE_MODE; break; default: dev_warn(mac_dev->dev, "cannot configure dTSEC for %s\n",
@@ -923,7 +929,8 @@ static void dtsec_mac_config(struct phylink_config *config, unsigned int mode, return; } - iowrite32be(tmp, ®s->ecntrl); + iowrite32be(ecntrl, ®s->ecntrl); + iowrite32be(maccfg2, ®s->maccfg2); } static void dtsec_link_up(struct phylink_config *config, struct phy_device *phy,
--
2.47.3