[PATCH net-next 2/2] net: phy: add Rust reference driver for ET1011C

@@ -254,6 +254,15 @@ config LSI_ET1011C_PHY
 	help
 	  Supports the LSI ET1011C PHY.
 
+config ET1011C_RUST_PHY
+	bool "Rust reference driver for LSI ET1011C PHY"
+	depends on RUST_PHYLIB_ABSTRACTIONS && LSI_ET1011C_PHY
+	help
+	  Uses the Rust reference driver for LSI ET1011C PHY
+	  (et1011c_rust.ko). The features and behavior are
+	  equivalent to the C driver. Selecting this option builds
+	  the Rust version instead of the C version.
+
 config MARVELL_PHY
 	tristate "Marvell Alaska PHYs"
 	help

@@ -62,7 +62,11 @@ obj-$(CONFIG_DP83TG720_PHY)	+= dp83tg720.o
 obj-$(CONFIG_FIXED_PHY)		+= fixed_phy.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_INTEL_XWAY_PHY)	+= intel-xway.o
-obj-$(CONFIG_LSI_ET1011C_PHY)	+= et1011c.o
+ifdef CONFIG_ET1011C_RUST_PHY
+  obj-$(CONFIG_LSI_ET1011C_PHY)	+= et1011c_rust.o
+else
+  obj-$(CONFIG_LSI_ET1011C_PHY)	+= et1011c.o
+endif
 obj-$(CONFIG_LXT_PHY)		+= lxt.o
 obj-$(CONFIG_MARVELL_10G_PHY)	+= marvell10g.o
 obj-$(CONFIG_MARVELL_PHY)	+= marvell.o

@@ -0,0 +1,70 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2026 Artem Lytkin <iprintercanon@gmail.com>
+
+//! Rust LSI ET1011C PHY driver
+//!
+//! C version of this driver: [`drivers/net/phy/et1011c.c`](./et1011c.c)
+
+use kernel::{
+    net::phy::{self, reg::C22, DeviceId, Driver},
+    prelude::*,
+    uapi,
+};
+
+kernel::module_phy_driver! {
+    drivers: [PhyET1011C],
+    device_table: [
+        DeviceId::new_with_driver::<PhyET1011C>()
+    ],
+    name: "rust_et1011c_phy",
+    authors: ["Artem Lytkin <iprintercanon@gmail.com>"],
+    description: "Rust LSI ET1011C PHY driver",
+    license: "GPL",
+}
+
+const ET1011C_STATUS_REG: C22 = C22::vendor_specific::<0x1A>();
+const ET1011C_CONFIG_REG: C22 = C22::vendor_specific::<0x16>();
+
+const ET1011C_SPEED_MASK: u16 = 0x0300;
+const ET1011C_GIGABIT_SPEED: u16 = 0x0200;
+const ET1011C_TX_FIFO_MASK: u16 = 0x3000;
+const ET1011C_TX_FIFO_DEPTH_16: u16 = 0x1000;
+const ET1011C_GMII_INTERFACE: u16 = 0x0002;
+const ET1011C_SYS_CLK_EN: u16 = 0x0010;
+
+const BMCR_FULLDPLX: u16 = uapi::BMCR_FULLDPLX as u16;
+const BMCR_SPEED100: u16 = uapi::BMCR_SPEED100 as u16;
+const BMCR_SPEED1000: u16 = uapi::BMCR_SPEED1000 as u16;
+const BMCR_ANENABLE: u16 = uapi::BMCR_ANENABLE as u16;
+const BMCR_RESET: u16 = uapi::BMCR_RESET as u16;
+
+struct PhyET1011C;
+
+#[vtable]
+impl Driver for PhyET1011C {
+    const NAME: &'static CStr = c"ET1011C";
+    const PHY_DEVICE_ID: DeviceId = DeviceId::new_with_model_mask(0x0282f014);
+
+    fn config_aneg(dev: &mut phy::Device) -> Result {
+        let ctl = dev.read(C22::BMCR)?;
+        let ctl = ctl & !(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE);
+        dev.write(C22::BMCR, ctl | BMCR_RESET)?;
+        dev.genphy_config_aneg()
+    }
+
+    fn read_status(dev: &mut phy::Device) -> Result<u16> {
+        dev.genphy_read_status::<C22>()?;
+
+        let val = dev.read(ET1011C_STATUS_REG)?;
+        if (val & ET1011C_SPEED_MASK) == ET1011C_GIGABIT_SPEED {
+            let cfg = dev.read(ET1011C_CONFIG_REG)?;
+            let cfg = cfg & !ET1011C_TX_FIFO_MASK;
+            dev.write(
+                ET1011C_CONFIG_REG,
+                cfg | ET1011C_GMII_INTERFACE | ET1011C_SYS_CLK_EN | ET1011C_TX_FIFO_DEPTH_16,
+            )?;
+        }
+
+        Ok(0)
+    }
+}