Add device tree nodes for PCIe controller and USB3 XHCI host
controller on MT7981B SoC. Both controllers share the USB3 PHY
which can be configured for either USB3 or PCIe operation.

The USB3 XHCI controller supports USB 2.0 and USB 3.0 SuperSpeed
operation. The PCIe controller is compatible with PCIe Gen2
specifications.

Also add the topmisc syscon node required for USB/PCIe PHY
multiplexing.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Sjoerd Simons <redacted>
---
V1 -> V2: Keep xhci reg and phys properties in single lines
---
 arch/arm64/boot/dts/mediatek/mt7981b.dtsi | 80 +++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)

diff --git a/arch/arm64/boot/dts/mediatek/mt7981b.dtsi b/arch/arm64/boot/dts/mediatek/mt7981b.dtsi
index 416096b80770..d3f37413413e 100644
--- a/arch/arm64/boot/dts/mediatek/mt7981b.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7981b.dtsi

@@ -2,6 +2,7 @@

 #include <dt-bindings/clock/mediatek,mt7981-clk.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/reset/mt7986-resets.h>

 / {

@@ -223,6 +224,55 @@ auxadc: adc@1100d000 {
                        status = "disabled";
                };

+               xhci: usb@11200000 {
+                       compatible = "mediatek,mt7986-xhci", "mediatek,mtk-xhci";
+                       reg = <0 0x11200000 0 0x2e00>, <0 0x11203e00 0 0x0100>;
+                       reg-names = "mac", "ippc";
+                       clocks = <&infracfg CLK_INFRA_IUSB_SYS_CK>,
+                                <&infracfg CLK_INFRA_IUSB_CK>,
+                                <&infracfg CLK_INFRA_IUSB_133_CK>,
+                                <&infracfg CLK_INFRA_IUSB_66M_CK>,
+                                <&topckgen CLK_TOP_U2U3_XHCI_SEL>;
+                       clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck", "xhci_ck";
+                       interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+                       phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
+                       status = "disabled";
+               };
+
+               pcie: pcie@11280000 {
+                       compatible = "mediatek,mt7981-pcie",
+                                    "mediatek,mt8192-pcie";
+                       reg = <0 0x11280000 0 0x4000>;
+                       reg-names = "pcie-mac";
+                       ranges = <0x82000000 0 0x20000000
+                                 0x0 0x20000000 0 0x10000000>;
+                       bus-range = <0x00 0xff>;
+                       clocks = <&infracfg CLK_INFRA_IPCIE_CK>,
+                                <&infracfg CLK_INFRA_IPCIE_PIPE_CK>,
+                                <&infracfg CLK_INFRA_IPCIER_CK>,
+                                <&infracfg CLK_INFRA_IPCIEB_CK>;
+                       clock-names = "pl_250m", "tl_26m", "peri_26m", "top_133m";
+                       device_type = "pci";
+                       phys = <&u3port0 PHY_TYPE_PCIE>;
+                       phy-names = "pcie-phy";
+                       interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+                       interrupt-map-mask = <0 0 0 7>;
+                       interrupt-map = <0 0 0 1 &pcie_intc 0>,
+                                       <0 0 0 2 &pcie_intc 1>,
+                                       <0 0 0 3 &pcie_intc 2>,
+                                       <0 0 0 4 &pcie_intc 3>;
+                       #address-cells = <3>;
+                       #interrupt-cells = <1>;
+                       #size-cells = <2>;
+                       status = "disabled";
+
+                       pcie_intc: interrupt-controller {
+                               interrupt-controller;
+                               #address-cells = <0>;
+                               #interrupt-cells = <1>;
+                       };
+               };
+
                pio: pinctrl@11d00000 {
                        compatible = "mediatek,mt7981-pinctrl";
                        reg = <0 0x11d00000 0 0x1000>,

@@ -252,6 +302,36 @@ mux {
                        };
                };

+               topmisc: topmisc@11d10000 {
+                       compatible = "mediatek,mt7981-topmisc", "syscon";
+                       reg = <0 0x11d10000 0 0x10000>;
+                       #clock-cells = <1>;