[PATCH net-next v7 4/6] arm64: dts: allwinner: a527: cubie-a5e: Enable second Ethernet port
From: Chen-Yu Tsai <wens@kernel.org>
Date: 2025-09-23 14:02:50
Also in:
linux-arm-kernel, linux-devicetree, linux-sunxi, lkml
Subsystem:
arm/allwinner sunxi soc support, the rest · Maintainers:
Chen-Yu Tsai, Jernej Skrabec, Samuel Holland, Linus Torvalds
From: Chen-Yu Tsai <redacted> On the Radxa Cubie A5E board, the second Ethernet controller, aka the GMAC200, is connected to a second external Maxio MAE0621A PHY. The PHY uses an external 25MHz crystal, and has the SoC's PJ16 pin connected to its reset pin. Enable the second Ethernet port. Also fix up the label for the existing external PHY connected to the first Ethernet port. An enable delay for the PHY supply regulator is added to make sure the PHY's internal regulators are fully powered and the PHY is operational. Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Chen-Yu Tsai <redacted> --- Changes since v1: - Switch to generic (tx|rx)-internal-delay-ps properties - Add PHY regulator delay --- .../dts/allwinner/sun55i-a527-cubie-a5e.dts | 28 +++++++++++++++++-- 1 file changed, 26 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
index f82a8d121697..bfdf1728cd14 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a527-cubie-a5e.dts@@ -14,6 +14,7 @@ / { aliases { ethernet0 = &gmac0; + ethernet1 = &gmac1; serial0 = &uart0; };
@@ -75,7 +76,7 @@ &ehci1 { &gmac0 { phy-mode = "rgmii-id"; - phy-handle = <&ext_rgmii_phy>; + phy-handle = <&ext_rgmii0_phy>; phy-supply = <®_cldo3>; allwinner,tx-delay-ps = <300>;
@@ -84,13 +85,24 @@ &gmac0 { status = "okay"; }; +&gmac1 { + phy-mode = "rgmii-id"; + phy-handle = <&ext_rgmii1_phy>; + phy-supply = <®_cldo4>; + + tx-internal-delay-ps = <300>; + rx-internal-delay-ps = <400>; + + status = "okay"; +}; + &gpu { mali-supply = <®_dcdc2>; status = "okay"; }; &mdio0 { - ext_rgmii_phy: ethernet-phy@1 { + ext_rgmii0_phy: ethernet-phy@1 { compatible = "ethernet-phy-ieee802.3-c22"; reg = <1>; reset-gpios = <&pio 7 8 GPIO_ACTIVE_LOW>; /* PH8 */
@@ -99,6 +111,16 @@ ext_rgmii_phy: ethernet-phy@1 { }; }; +&mdio1 { + ext_rgmii1_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + reset-gpios = <&pio 9 16 GPIO_ACTIVE_LOW>; /* PJ16 */ + reset-assert-us = <10000>; + reset-deassert-us = <150000>; + }; +}; + &mmc0 { vmmc-supply = <®_cldo3>; cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */
@@ -250,6 +272,8 @@ reg_cldo4: cldo4 { regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-name = "vcc-pj-phy"; + /* enough time for the PHY to fully power on */ + regulator-enable-ramp-delay = <150000>; }; reg_cpusldo: cpusldo {
--
2.47.3