Drew Fustini wrote:

May I suggest you just do

#define GMAC_RXCLK_DELAY	GENMASK(4, 0)

..and then use FIELD_PREP(GMAC_RXCLK_DELAY, x) directly instead of wrapping it
in the GMAC_RXCLK_DELAY_VAL() macro.
This goes for GMAC_TXCLK_DELAY_{MASK,VAL} and GMAC_PLLCLK_DIV_{MASK,NUM} below
too.

+#define GMAC_TXCLK_DELAY_CTRL		0x08
+#define  GMAC_TXCLK_BYPASS		BIT(15)
+#define  GMAC_TXCLK_INVERT		BIT(14)
+#define  GMAC_TXCLK_DELAY_MASK		GENMASK(4, 0)
+#define  GMAC_TXCLK_DELAY_VAL(x)	FIELD_PREP(GMAC_RXCLK_DELAY_MASK, (x))
+#define GMAC_PLLCLK_DIV			0x0c
+#define  GMAC_PLLCLK_DIV_EN		BIT(31)
+#define  GMAC_PLLCLK_DIV_MASK		GENMASK(7, 0)
+#define  GMAC_PLLCLK_DIV_NUM(x)		FIELD_PREP(GMAC_PLLCLK_DIV_MASK, (x))
+#define GMAC_GTXCLK_SEL			0x18
+#define  GMAC_GTXCLK_SEL_PLL		BIT(0)
+#define GMAC_INTF_CTRL			0x1c
+#define  PHY_INTF_MASK			BIT(0)
+#define  PHY_INTF_RGMII			FIELD_PREP(PHY_INTF_MASK, 1)
+#define  PHY_INTF_MII_GMII		FIELD_PREP(PHY_INTF_MASK, 0)
+#define GMAC_TXCLK_OEN			0x20
+#define  TXCLK_DIR_MASK			BIT(0)
+#define  TXCLK_DIR_OUTPUT		FIELD_PREP(TXCLK_DIR_MASK, 0)
+#define  TXCLK_DIR_INPUT		FIELD_PREP(TXCLK_DIR_MASK, 1)
+
+#define GMAC_GMII_RGMII_RATE	125000000
+#define GMAC_MII_RATE		25000000
+
+struct thead_dwmac {
+	struct plat_stmmacenet_data *plat;
+	void __iomem *apb_base;
+	struct device *dev;
+};
+
+static int thead_dwmac_set_phy_if(struct plat_stmmacenet_data *plat)
+{
+	struct thead_dwmac *dwmac = plat->bsp_priv;
+	u32 phyif;
+
+	switch (plat->mac_interface) {
+	case PHY_INTERFACE_MODE_MII:
+		phyif = PHY_INTF_MII_GMII;
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		phyif = PHY_INTF_RGMII;
+		break;
+	default:
+		dev_err(dwmac->dev, "unsupported phy interface %d\n",
+			plat->mac_interface);
+		return -EINVAL;
+	}
+
+	writel(phyif, dwmac->apb_base + GMAC_INTF_CTRL);
+	return 0;
+}
+
+static int thead_dwmac_set_txclk_dir(struct plat_stmmacenet_data *plat)
+{
+	struct thead_dwmac *dwmac = plat->bsp_priv;
+	u32 txclk_dir;
+
+	switch (plat->mac_interface) {
+	case PHY_INTERFACE_MODE_MII:
+		txclk_dir = TXCLK_DIR_INPUT;
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		txclk_dir = TXCLK_DIR_OUTPUT;
+		break;
+	default:
+		dev_err(dwmac->dev, "unsupported phy interface %d\n",
+			plat->mac_interface);
+		return -EINVAL;
+	}
+
+	writel(txclk_dir, dwmac->apb_base + GMAC_TXCLK_OEN);
+	return 0;
+}
+
+static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int mode)
+{
+	struct plat_stmmacenet_data *plat;
+	struct thead_dwmac *dwmac = priv;
+	unsigned long rate;
+	u32 div, reg;
+
+	plat = dwmac->plat;
+
+	switch (plat->mac_interface) {
+	/* For MII, rxc/txc is provided by phy */
+	case PHY_INTERFACE_MODE_MII:
+		return;
+
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		rate = clk_get_rate(plat->stmmac_clk);
+		if (!rate || rate % GMAC_GMII_RGMII_RATE != 0 ||
+		    rate % GMAC_MII_RATE != 0) {
+			dev_err(dwmac->dev, "invalid gmac rate %ld\n", rate);
+			return;
+		}
+
+		writel(FIELD_PREP(GMAC_PLLCLK_DIV_EN, 0), dwmac->apb_base + GMAC_PLLCLK_DIV);
+
+		switch (speed) {
+		case SPEED_1000:
+			div = rate / GMAC_GMII_RGMII_RATE;
+			break;
+		case SPEED_100:
+			div = rate / GMAC_MII_RATE;
+			break;
+		case SPEED_10:
+			div = rate * 10 / GMAC_MII_RATE;
+			break;
+		default:
+			dev_err(dwmac->dev, "invalid speed %u\n", speed);
+			return;
+		}
+
+		reg = FIELD_PREP(GMAC_PLLCLK_DIV_EN, 1) |
+		      FIELD_PREP(GMAC_PLLCLK_DIV_MASK, GMAC_PLLCLK_DIV_NUM(div));

..and here is an example why. You accidentally end up using
FIELD_PREP() twice here.

+		writel(reg, dwmac->apb_base + GMAC_PLLCLK_DIV);
+		break;
+	default:
+		dev_err(dwmac->dev, "unsupported phy interface %d\n",
+			plat->mac_interface);
+		return;
+	}
+}
+
+static int thead_dwmac_enable_clk(struct plat_stmmacenet_data *plat)
+{
+	struct thead_dwmac *dwmac = plat->bsp_priv;
+	u32 reg;
+
+	switch (plat->mac_interface) {
+	case PHY_INTERFACE_MODE_MII:
+		reg = GMAC_RX_CLK_EN | GMAC_TX_CLK_EN;
+		break;
+
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		/* use pll */
+		writel(GMAC_GTXCLK_SEL_PLL, dwmac->apb_base + GMAC_GTXCLK_SEL);
+		reg = GMAC_TX_CLK_EN | GMAC_TX_CLK_N_EN | GMAC_TX_CLK_OUT_EN |
+		      GMAC_RX_CLK_EN | GMAC_RX_CLK_N_EN;
+		break;
+
+	default:
+		dev_err(dwmac->dev, "unsupported phy interface %d\n",
+			plat->mac_interface);
+		return -EINVAL;
+	}
+
+	writel(reg, dwmac->apb_base + GMAC_CLK_EN);
+	return 0;
+}
+
+static int thead_dwmac_init(struct platform_device *pdev, void *priv)
+{
+	struct thead_dwmac *dwmac = priv;
+	int ret;
+
+	ret = thead_dwmac_set_phy_if(dwmac->plat);
+	if (ret)
+		return ret;
+
+	ret = thead_dwmac_set_txclk_dir(dwmac->plat);
+	if (ret)
+		return ret;
+
+	writel(GMAC_RXCLK_DELAY_VAL(0), dwmac->apb_base + GMAC_RXCLK_DELAY_CTRL);
+	writel(GMAC_TXCLK_DELAY_VAL(0), dwmac->apb_base + GMAC_TXCLK_DELAY_CTRL);

I know Jisheng's original driver also did this too, but here you
unconditionally set both registers to 0 including the bypass and invert bits.
I'd suggest you either do

  writel(0, dwmac->apb_base + GMAC_RXCLK_DELAY_CTRL);
  writel(0, dwmac->apb_base + GMAC_TXCLK_DELAY_CTRL);

..to make this obvious, or do a proper read-modify-write to change just the
FIELD_PREP()'d bits.

+
+	return thead_dwmac_enable_clk(dwmac->plat);
+}
+
+static int thead_dwmac_probe(struct platform_device *pdev)
+{
+	struct stmmac_resources stmmac_res;
+	struct plat_stmmacenet_data *plat;
+	struct thead_dwmac *dwmac;
+	void __iomem *apb;
+	int ret;
+
+	ret = stmmac_get_platform_resources(pdev, &stmmac_res);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret,
+				     "failed to get resources\n");

Here you're not capitalizing the error message.

+
+	plat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac);
+	if (IS_ERR(plat))
+		return dev_err_probe(&pdev->dev, PTR_ERR(plat),
+				     "dt configuration failed\n");
+
+	dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
+	if (!dwmac)
+		return -ENOMEM;
+
+	apb = devm_platform_ioremap_resource(pdev, 1);
+	if (IS_ERR(apb))
+		return dev_err_probe(&pdev->dev, PTR_ERR(apb),
+				     "Failed to remap gmac apb registers\n");

..and here you are. Please be consistent in the whole driver.

+
+	dwmac->dev = &pdev->dev;
+	dwmac->plat = plat;
+	dwmac->apb_base = apb;
+	plat->bsp_priv = dwmac;
+	plat->fix_mac_speed = thead_dwmac_fix_speed;
+	plat->init = thead_dwmac_init;
+
+	return devm_stmmac_pltfr_probe(pdev, plat, &stmmac_res);
+}
+
+static const struct of_device_id thead_dwmac_match[] = {
+	{ .compatible = "thead,th1520-gmac" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, thead_dwmac_match);
+
+static struct platform_driver thead_dwmac_driver = {
+	.probe = thead_dwmac_probe,
+	.driver = {
+		.name = "thead-dwmac",
+		.pm = &stmmac_pltfr_pm_ops,
+		.of_match_table = thead_dwmac_match,
+	},
+};
+module_platform_driver(thead_dwmac_driver);
+
+MODULE_AUTHOR("Jisheng Zhang [off-list ref]");
+MODULE_AUTHOR("Drew Fustini [off-list ref]");
+MODULE_DESCRIPTION("T-HEAD DWMAC platform driver");
+MODULE_LICENSE("GPL");

--
2.34.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv