[PATCH net-next v6 5/7] net: stmmac: Signal to PHY/PCS drivers to keep RX clock on

From
Romain Gantois <romain.gantois@bootlin.com>
Date
2024-03-11 09:56:08
Also in
linux-arm-kernel, linux-renesas-soc
Reply to
Romain Gantois, 2024-03-11
There is a reocurring issue with stmmac controllers where the MAC fails to
initialize its hardware if an RX clock signal isn't provided on the MAC/PHY
link.

This causes issues when PHY or PCS devices either go into suspend while
cutting the RX clock or do not bring the clock signal up early enough for
the MAC to initialize successfully.

Set the mac_requires_rxc flag in the stmmac phylink config so that PHY/PCS
drivers know to keep the RX clock up at all times.

Reported-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/all/20230202081559.3553637-1-xiaoning.wang@nxp.com/ (local)
Reported-by: Clément Léger <redacted>
Link: https://lore.kernel.org/linux-arm-kernel/20230116103926.276869-4-clement.leger@bootlin.com/ (local)
Co-developed-by: Russell King (Oracle) <redacted>
Signed-off-by: Russell King (Oracle) <redacted>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 7 +++++++
 1 file changed, 7 insertions(+)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 79844dbe4258..2290f4808d7e 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1218,6 +1218,9 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 	priv->phylink_config.type = PHYLINK_NETDEV;
 	priv->phylink_config.mac_managed_pm = true;
 
+	/* Stmmac always requires an RX clock for hardware initialization */
+	priv->phylink_config.mac_requires_rxc = true;
+
 	mdio_bus_data = priv->plat->mdio_bus_data;
 	if (mdio_bus_data)
 		priv->phylink_config.ovr_an_inband =
@@ -3408,6 +3411,10 @@ static int stmmac_hw_setup(struct net_device *dev, bool ptp_register)
 	u32 chan;
 	int ret;
 
+	/* Make sure RX clock is enabled */
+	if (priv->hw->phylink_pcs)
+		phylink_pcs_pre_init(priv->phylink, priv->hw->phylink_pcs);
+
 	/* DMA initialization and SW reset */
 	ret = stmmac_init_dma_engine(priv);
 	if (ret < 0) {
-- 
2.44.0
Thread (9 messages) 9 messages, 2 authors, last reply 2024-03-12
Keyboard shortcuts
hback out one level
jnext message in thread / next series-diff position
kprevious message in thread / previous series-diff position
ldrill in
Escclose help / fold thread tree
?toggle this help