Jamal Hadi Salim wrote:
Introduce P4 tc classifier. A tc filter instantiated on this classifier
is used to bind a P4 pipeline to one or more netdev ports. To use P4
classifier you must specify a pipeline name that will be associated to
this filter, a s/w parser and datapath ebpf program. The pipeline must have
already been created via a template.
For example, if we were to add a filter to ingress of network interface
device $P0 and associate it to P4 pipeline simple_l3 we'd issue the
following command:
tc filter add dev $P0 parent ffff: protocol all prio 6 p4 pname simple_l3 \
action bpf obj $PARSER.o section prog/tc-parser \
action bpf obj $PROGNAME.o section prog/tc-ingress
$PROGNAME.o and $PARSER.o is a compilation of the eBPF programs generated
by the P4 compiler and will be the representation of the P4 program.
Note that filter understands that $PARSER.o is a parser to be loaded
at the tc level. The datapath program is merely an eBPF action.
Note we do support a distinct way of loading the parser as opposed to
making it be an action, the above example would be:
tc filter add dev $P0 parent ffff: protocol all prio 6 p4 pname simple_l3 \
prog type tc obj $PARSER.o ... \
action bpf obj $PROGNAME.o section prog/tc-ingress
We support two types of loadings of these initial programs in the pipeline
and differentiate between what gets loaded at tc vs xdp by using syntax of
either "prog type tc obj" or "prog type xdp obj"
For XDP:
tc filter add dev $P0 ingress protocol all prio 1 p4 pname simple_l3 \
prog type xdp obj $PARSER.o section parser/xdp \
pinned_link /sys/fs/bpf/mylink \
action bpf obj $PROGNAME.o section prog/tc-ingress
The theory of operations is as follows:
You've lost me here. You have a BPF parser program and some BPF actions.
Why not have the parser program just call the BPF action?
It seems the action is based on LPM or some software like TCAM. So
steps in BPF would be,
Parse -> bpf_map_lookup to find action -> call action
Just use the normal way to load the bpf program through 'tc' or 'xdp'.
Or its all about hardware, but I still have no idea how this BPF parser
gets into hardware and how these actions get there. So we can't even
evaluate what that looks like.
================================1. PARSING================================
The packet first encounters the parser.
The parser is implemented in ebpf residing either at the TC or XDP
level. The parsed header values are stored in a shared eBPF map.
When the parser runs at XDP level, we load it into XDP using tc filter
command and pin it to a file.
=============================2. ACTIONS=============================
In the above example, the P4 program (minus the parser) is encoded in an
action($PROGNAME.o). It should be noted that classical tc actions
continue to work:
IOW, someone could decide to add a mirred action to mirror all packets
after or before the ebpf action.
tc filter add dev $P0 parent ffff: protocol all prio 6 p4 pname simple_l3 \
prog type tc obj $PARSER.o section parser/tc-ingress \
action bpf obj $PROGNAME.o section prog/tc-ingress \
action mirred egress mirror index 1 dev $P1 \
action bpf obj $ANOTHERPROG.o section mysect/section-1
It should also be noted that it is feasible to split some of the ingress
datapath into XDP first and more into TC later (as was shown above for
example where the parser runs at XDP level). YMMV.
Co-developed-by: Victor Nogueira <redacted>
Signed-off-by: Victor Nogueira <redacted>
Co-developed-by: Pedro Tammela <redacted>
Signed-off-by: Pedro Tammela <redacted>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>