[RESEND PATCH v4 8/8] bpf ppc32: Access only if addr is kernel address
From: Hari Bathini <hbathini@linux.ibm.com>
Date: 2021-10-12 12:34:36
Also in:
bpf, linuxppc-dev
Subsystem:
bpf jit for powerpc (32-bit and 64-bit), bpf [general] (safe dynamic programs and tools), linux for powerpc (32-bit and 64-bit), the rest · Maintainers:
Hari Bathini, Christophe Leroy, Alexei Starovoitov, Daniel Borkmann, Andrii Nakryiko, Eduard Zingerman, Kumar Kartikeya Dwivedi, Madhavan Srinivasan, Michael Ellerman, Linus Torvalds
With KUAP enabled, any kernel code which wants to access userspace needs to be surrounded by disable-enable KUAP. But that is not happening for BPF_PROBE_MEM load instruction. Though PPC32 does not support read protection, considering the fact that PTR_TO_BTF_ID (which uses BPF_PROBE_MEM mode) could either be a valid kernel pointer or NULL but should never be a pointer to userspace address, execute BPF_PROBE_MEM load only if addr is kernel address, otherwise set dst_reg=0 and move on. This will catch NULL, valid or invalid userspace pointers. Only bad kernel pointer will be handled by BPF exception table. [Alexei suggested for x86] Suggested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Hari Bathini <hbathini@linux.ibm.com> Reviewed-by: Christophe Leroy <redacted> --- Changes in v4: * Adjusted the emit code to avoid using temporary reg. arch/powerpc/net/bpf_jit_comp32.c | 34 +++++++++++++++++++++++++++++++ 1 file changed, 34 insertions(+)
diff --git a/arch/powerpc/net/bpf_jit_comp32.c b/arch/powerpc/net/bpf_jit_comp32.c
index 5dc45e393d1d..d3a52cd42f53 100644
--- a/arch/powerpc/net/bpf_jit_comp32.c
+++ b/arch/powerpc/net/bpf_jit_comp32.c@@ -820,6 +820,40 @@ int bpf_jit_build_body(struct bpf_prog *fp, u32 *image, struct codegen_context * case BPF_LDX | BPF_PROBE_MEM | BPF_W: case BPF_LDX | BPF_MEM | BPF_DW: /* dst = *(u64 *)(ul) (src + off) */ case BPF_LDX | BPF_PROBE_MEM | BPF_DW: + /* + * As PTR_TO_BTF_ID that uses BPF_PROBE_MEM mode could either be a valid + * kernel pointer or NULL but not a userspace address, execute BPF_PROBE_MEM + * load only if addr is kernel address (see is_kernel_addr()), otherwise + * set dst_reg=0 and move on. + */ + if (BPF_MODE(code) == BPF_PROBE_MEM) { + PPC_LI32(_R0, TASK_SIZE - off); + EMIT(PPC_RAW_CMPLW(src_reg, _R0)); + PPC_BCC(COND_GT, (ctx->idx + 5) * 4); + EMIT(PPC_RAW_LI(dst_reg, 0)); + /* + * For BPF_DW case, "li reg_h,0" would be needed when + * !fp->aux->verifier_zext. Emit NOP otherwise. + * + * Note that "li reg_h,0" is emitted for BPF_B/H/W case, + * if necessary. So, jump there insted of emitting an + * additional "li reg_h,0" instruction. + */ + if (size == BPF_DW && !fp->aux->verifier_zext) + EMIT(PPC_RAW_LI(dst_reg_h, 0)); + else + EMIT(PPC_RAW_NOP()); + /* + * Need to jump two instructions instead of one for BPF_DW case + * as there are two load instructions for dst_reg_h & dst_reg + * respectively. + */ + if (size == BPF_DW) + PPC_JMP((ctx->idx + 3) * 4); + else + PPC_JMP((ctx->idx + 2) * 4); + } + switch (size) { case BPF_B: EMIT(PPC_RAW_LBZ(dst_reg, src_reg, off));
--
2.31.1