Re: [PATCH net-next 1/2] rtnetlink: Add new RTM_GETEECSTATE message to get SyncE status

On Tue, 7 Sep 2021 08:50:55 +0000 Machnikowski, Maciej wrote:

quoted

quoted

The frequency source can be either pre-set statically, negotiated using
ESMC QL-levels (if working in QL-Enabled mode), or follow automatic
fallback inside the device. This  flag gives feedback about the validity
of recovered clock coming from a given port and is useful when you
enable multiple recovered clocks on more than one port in
active-passive model. In that case the "driving" port may change
dynamically, so it's a good idea to have some interface to reflect that.  

The ESMC messages are handled by Linux or some form of firmware?
I don't see how you can implement any selection policy with a read-only
API.  

It can be either in FW or in Linux - depending on the deployment.
We try to define the API that would enable Linux to manage that.

We should implement the API for Linux to manage things from the get go.

EEC state will be read-only, but the recovered clock management part
will allow changes for QL-disabled SyncE deployments that only need
to see if the clock they receive on a given port is valid or not.

quoted

In general it would be more natural to place a "source id" at the
DPLL/clock, the "source" flag seems to mark the wrong end of the
relationship. If there ever are multiple consumers we won't be able
to tell which "target" the "source" is referring to. Hard to judge
how much of a problem that could be by looking at a small slice of
the system.  

The DPLL will operate on pins, so it will have a pin connected from the
MAC/PHY that will have the recovered clock, but the recovered clock
can be enabled from any port/lane. That information is kept in the 
MAC/PHY and the DPLL side will not be aware who it belongs to.

So the clock outputs are muxed to a single pin at the Ethernet IP
level, in your design. I wonder if this is the common implementation
and therefore if it's safe to bake that into the API. Input from other
vendors would be great...

Also do I understand correctly that the output of the Ethernet IP 
is just the raw Rx clock once receiver is locked and the DPLL which 
enum if_synce_state refers to is in the time IP, that DPLL could be
driven by GNSS etc?

We can come up with a better name,  but think of it like:
You have multiport device (switch/NIC). One port is recovering
the clock, the PHY/MAC outputs that clock through the pin
to the EEC (DPLL). The DPLL knows if it locked to the signal coming
from the multiport PHY/MAC, but it doesn't know which port is the one
that generates that clock signal. All other ports can also present the
"locked" state, but they are following the clock that was received
in the chosen port. If we drop this flag we won't be able to easily tell
which port/lane drives the recovered clock.
In short: the port with that flag on is following the network clock
and leading clock of other ports of the multiport device.

In the most basic SyncE deployment you can put the passive DPLL that
will only give you the lock/holdover/unlocked info and just use this flag 
to know who currently drives the DPLL.

quoted

quoted

That's where sysfs file be useful. When I add the implementation for
recovered clock configuration, the sysfs may be used as standalone
interface for configuring them when no dynamic change is needed.  

I didn't get that. Do you mean using a sysfs file to configure
the parameters of the DPLL?  

Only the PHY/MAC side of thing which is recovered clock configuration
and the ECC state.
 

quoted

If the DPLL has its own set of concerns we should go ahead and create
explicit object / configuration channel for it.

Somehow I got it into my head that you care mostly about transmitting
the clock, IOW recovering it from one port and using on another but
that's probably not even a strong use case for you or NICs in general :S  

This is the right thinking. The DPLL can also have different external sources,
like the GNSS, and can also drive different output clocks. But for the most
basic SyncE implementation, which only runs on a recovered clock, we won't
need the DPLL subsystem.

The GNSS pulse would come in over an external pin, tho, right? Your
earlier version of the patchset had GNSS as an enum value, how would
the driver / FW know that a given pin means GNSS?

quoted

quoted

Could you suggest where to add that? Grepping for ndo_ don't give much.
I can add a new synce.rst file if it makes sense.  

New networking/synce.rst file makes perfect sense to me. And perhaps
link to it from driver-api/ptp.rst.  

OK will try to come up with something there