Re: [PATCH net-next 1/2] net: dsa: rtl8366rb: support bridge offloading

On Mon, Aug 30, 2021 at 11:22:11PM +0200, Linus Walleij wrote:

On Mon, Aug 30, 2021 at 10:12 AM Vladimir Oltean [off-list ref] wrote:

quoted

quoted

+/* Port isolation registers */
+#define RTL8366RB_PORT_ISO_BASE              0x0F08
+#define RTL8366RB_PORT_ISO(pnum)     (RTL8366RB_PORT_ISO_BASE + (pnum))
+#define RTL8366RB_PORT_ISO_EN                BIT(0)
+#define RTL8366RB_PORT_ISO_PORTS_MASK        GENMASK(7, 1)

If RTL8366RB_NUM_PORTS is 6, then why is RTL8366RB_PORT_ISO_PORTS_MASK a
7-bit field?

It's a 6 bit field actually from bit 1 to bit 7 just shifted up one
bit because bit 0 is "enable".

Understood the part about bit 0 being "ENABLE".
But from bit 1 to bit 7, I count 7 bits set....

quoted

Also, it would be nice if you could do some minimal isolation at the
level of the FDB lookup. Currently, if I am not mistaken, a port will
perform FDB lookup even if it is standalone, and it might find an FDB
entry for a given {MAC DA, VLAN ID} pair that belongs to a port outside
of its isolation mask, so forwarding will be blocked and that packet
will be dropped (instead of the expected behavior which is for that
packet to be forwarded to the CPU).

Normally the expectation is that this FDB-level isolation can be achieved
by configuring the VLANs of one bridge to use a filter ID that is
different from the VLANs of another bridge, and the port-based default
VLAN of standalone ports to use yet another filter ID. This is yet
another reason to disable learning on standalone ports, so that their
filter ID never contains any FDB entry, and packets are always flooded
to their only possible destination, the CPU port.

Currently in DSA we do not offer a streamlined way for you to determine
what filter ID to use for a certain VLAN belonging to a certain bridge,
but at the very least you can test FDB isolation between standalone
ports and bridged ports. The simplest way to do that, assuming you
already have a forwarding setup with 2 switch ports swp0 and swp1, is to
enable CONFIG_BONDING=y, and then:

ip link add br0 type bridge
ip link set bond0 master br0
ip link set swp1 master bond0
ip link set swp0 master br0

Then ping between station A attached to swp0 and station B attached to
swp1.

Because swp1 cannot offload bond0, it will fall back to software
forwarding and act as standalone, i.e. what you had up till now.
With hardware address learning enabled on swp0 (a port that offloads
br0), it will learn station A's source MAC address. Then when swp1 needs
to send a packet to station A's destination MAC address, it would be
tempted to look up the FDB, find that address, and forward to swp0. But
swp0 is isolated from swp1. If you use a filter ID for standalone ports
and another filter ID for bridged ports you will avoid that problem, and
you will also lay the groundwork for the full FDB isolation even between
bridges that will be coming during the next development cycle.

If you feel that the second part is too much for now, you can just add
the extra callbacks for address learning and flushing (although I do
have some genuine concerns about how reliable was the software forwarding
with this driver, seeing that right now it enables hardware learning
unconditionally). Is there something that isolates FDB lookups already?

Ugh that was massive, I'm not that smart ;)

I kinda understand it but have no idea how to achieve this with
the current hardware, driver and vendor code mess.

I prefer to fix the first part for now.

Okay, no problem, I suppose FDB isolation can be revisited as part of
the larger rework I've got planned for the next kernel.